X6800 Datasheet, PDF (27/122 Pages) Intel Corporation – Core2 Extreme Processor

Electrical Specifications
2.7.1
Table 9.
FSB Signal Groups
The front side bus signals have been combined into groups by buffer type. GTL+ input
signals have differential input buffers, which use GTLREF[1:0] as a reference level. In
this document, the term “GTL+ Input” refers to the GTL+ input group as well as the
GTL+ I/O group when receiving. Similarly, “GTL+ Output” refers to the GTL+ output
group as well as the GTL+ I/O group when driving.
With the implementation of a source synchronous data bus comes the need to specify
two sets of timing parameters. One set is for common clock signals which are
dependent upon the rising edge of BCLK0 (ADS#, HIT#, HITM#, etc.) and the second
set is for the source synchronous signals which are relative to their respective strobe
lines (data and address) as well as the rising edge of BCLK0. Asychronous signals are
still present (A20M#, IGNNE#, etc.) and can become active at any time during the
clock cycle. Table 9 identifies which signals are common clock, source synchronous,
and asynchronous.
FSB Signal Groups
Signal Group
GTL+ Common
Clock Input
GTL+ Common
Clock I/O
Type
Synchronous to
BCLK[1:0]
Synchronous to
BCLK[1:0]
Signals¹
BPRI#, DEFER#, RESET#, RS[2:0]#, TRDY#
ADS#, BNR#, BPM[5:0]#, BR0#, DBSY#, DRDY#,
HIT#, HITM#, LOCK#
GTL+ Source
Synchronous I/O
Synchronous to
assoc. strobe
Signals
REQ[4:0]#, A[16:3]#³
A[35:17]#³
D[15:0]#, DBI0#
D[31:16]#, DBI1#
D[47:32]#, DBI2#
D[63:48]#, DBI3#
Associated Strobe
ADSTB0#
ADSTB1#
DSTBP0#, DSTBN0#
DSTBP1#, DSTBN1#
DSTBP2#, DSTBN2#
DSTBP3#, DSTBN3#
GTL+ Strobes
Synchronous to
BCLK[1:0]
CMOS
Open Drain Output
Open Drain Input/
Output
FSB Clock
Clock
Power/Other
ADSTB[1:0]#, DSTBP[3:0]#, DSTBN[3:0]#
A20M#, IGNNE#, INIT#, LINT0/INTR, LINT1/NMI,
SMI#, STPCLK#, PWRGOOD, TCK, TDI, TMS, TRST#,
BSEL[2:0], VID[6:1]
FERR#/PBE#, IERR#, THERMTRIP#, TDO
PROCHOT#⁴
BCLK[1:0], ITP_CLK[1:0]²
VCC, VTT, VCCA, VCCIOPLL, VCCPLL, VSS, VSSA,
GTLREF[1:0], COMP[8,3:0], RESERVED, TESTHI[13:0],
VCC_SENSE, VCC_MB_REGULATION, VSS_SENSE,
VSS_MB_REGULATION, DBR#², VTT_OUT_LEFT,
VTT_OUT_RIGHT, VTT_SEL, FCx, PECI, MSID[1:0]
NOTES:
1.
Refer to Section 4.2 for signal descriptions.
2.
In processor systems where no debug port is implemented on the system board, these
signals are used to support a debug port interposer. In systems with the debug port
implemented on the system board, these signals are no connects.
3.
The value of these signals during the active-to-inactive edge of RESET# defines the
processor configuration options. See Section 6.1 for details.
4.
PROCHOT# signal type is open drain output and CMOS input.
Datasheet
27