BCM4319XKUBGT Datasheet, PDF (59/84 Pages) Cypress Semiconductor – Single-Chip IEEE 802.11™ a/b/g/n MAC/Baseband/ Radio with Integrated SDIO and USB Interfaces

BCM4319 Preliminary Data Sheet
Recommended Operating Conditions and DC Characteristics
Recommended Operating Conditions and DC Characteristics
Table 11: Recommended Operating Conditions and DC Characteristics
Value
Element
Symbol Minimum Typical
Maximum Unit
DC supply voltage for VBAT ^a
–
2.7 ^b
–
5.5^b
V
DC supply voltage for OTP, USB ^a
–
DC supply voltage for PA ^a
–
3.0
3.3
3.63 V
2.8^c
3.3
3.63 V
DC supply voltage for I/O^{a, d}
VDDO
1.62
3.3 or 1.8
3.63 V
DC supply voltage for core ^a
VDDC
1.176
1.225
1.30 V
1.2V Analog (Radio/AFE/PLL/XTAL/USB –
1.2)^a
1.176
1.225
1.30 V
2.5V USB^a
–
2.25
2.5
2.75 V
Input low voltage (VDDO = 3.3V)^e
V_IL
–
–
0.8 V
Input high voltage (VDDO = 3.3V)^e
V_IH
2.0
–
VDDO V
Input low voltage (VDDO = 1.8V)^e
V_IL
–
–
0.6 V
Input high voltage (VDDO = 1.8V)^e
V_IH
1.1
–
VDDO V
Input high voltage (WL_REG_ON pin)
V_IH
Output low voltage (IOL = 100 μA)
V_OL
Output high voltage (IOH = –100 μA)
V_OH
Input low current
I_IL
Input high current
I_IH
Output low current (VDDIO/VDDIO_RF) I_OL
Output high current (VDDIO/VDDIO_RF) I_OH
Output low current (VDDIO_SD)
I_OL
Output high current (VDDIO_SD)
I_OH
1.6
–
VDDO – 0.2V
–
–
–
–
–
–
–
3.6 V
–
0.2 V
–
–V
0.3
– μA
0.3
– μA
–
3.0 mA
–
3.0 mA
– Programmable: mA
2 to 12 mA
– _{(default 10 mA)} mA
a. Functional operation is not guaranteed outside these limits, and operation outside these limits for extended
periods can adversely affect long-term reliability of the device.
b. The BCM4319 is functional across this range of voltages. However, optimal RF performance specified in the
datasheet is only guaranteed while VBAT is between 3.0 and 5.25V.
c. With VBAT = 3.0V PALDO output = 3.0 –0.2 (dropout voltage) = 2.8V
d. The supported voltage range applies to all three I/O supplies: VDDIO, VDDIO_SD, and VDDIO_RF.
VDDIO and VDDIO_SD often use 1.8V signaling; however, VDDIO_RF tends to use a higher voltage rail, such
as 3.3V, because this supply rail is used for the BCM4319 RF switch and front-end control lines. RF front-end
components (such as transmit/receive switches) tend to require higher control voltages.
e. For any other VDDO from 1.8V to 3.3V (±10%), V_IH and V_IL are specified as V_IH = from 0.7 * VDDO to VDDO
and V_IL = from 0V to 0.2 * VDDO.
Broadcom^®
April 2, 2014 • 4319-DS05-R
Single-Chip IEEE 802.11™ a/b/g/n MAC/Baseband/Radio
Page 58