EVAL-ADUC831QSZ Datasheet, PDF (33/76 Pages) Analog Devices – MicroConverter®, 12-Bit ADCs and DACs with Embedded 62 kBytes Flash MCU

Using the DAC
The on-chip DAC architecture consists of a resistor string DAC
followed by an output buffer amplifier, the functional equivalent
of which is illustrated in Figure 21. Details of the actual DAC
architecture can be found in U.S. Patent Number 5969657
(www.uspto.gov). Features of this architecture include inherent
guaranteed monotonicity and excellent differential linearity.
V_DD
V_DD –50mV
V_DD –100mV
ADuC831
AV_DD
V_REF
R
R
R
R
R
ADuC831
OUTPUT
BUFFER
DAC0
HIGH Z
DISABLE
(FROM MCU)
Figure 21. Resistor String DAC Functional Equivalent
As illustrated in Figure 21, the reference source for each DAC is
user selectable in software. It can be either AV_DD or V_REF. In
0-to-AV_DD mode, the DAC output transfer function spans from
0 V to the voltage at the AV_DD pin. In 0-to-V_REF mode, the
DAC output transfer function spans from 0 V to the internal
V_REF, or if an external reference is applied, the voltage at the
V_REF pin. The DAC output buffer amplifier features a true rail-
to-rail output stage implementation. This means that, unloaded,
each output is capable of swinging to within less than 100 mV of
both AV_DD and ground. Moreover, the DAC’s linearity specifi-
cation (when driving a 10 kΩ resistive load to ground) is
guaranteed through the full transfer function except codes 0 to
100, and, in 0-to-AV_DD mode only, codes 3945 to 4095. Linear-
ity degradation near ground and V_DD is caused by saturation of
the output amplifier, and a general representation of its effects
(neglecting offset and gain error) is illustrated in Figure 22. The
dotted line in Figure 22 indicates the ideal transfer function,
and the solid line represents what the transfer function might
look like with endpoint nonlinearities due to saturation of the
output amplifier. Note that Figure 22 represents a transfer
function in 0-to-V_DD mode only. In 0-to-V_REF mode (with V_REF
< V_DD) the lower nonlinearity would be similar, but the upper
portion of the transfer function would follow the “ideal” line
right to the end (V_REF in this case, not V_DD), showing no signs
of endpoint linearity errors.
100mV
50mV
0mV
000H
FFFH
Figure 22. Endpoint Nonlinearities Due to Amplifier
Saturation
The end point nonlinearities conceptually illustrated in Figure
22 get worse as a function of output loading. Most of the
ADuC831’s data sheet specifications assume a 10 kΩ resistive
load to ground at the DAC output. As the output is forced to
source or sink more current, the nonlinear regions at the top or
bottom (respectively) of Figure 22 become larger. With larger
current demands, this can significantly limit output voltage
swing. Figure 23 and Figure 24 illustrate this behavior. It
should be noted that the upper trace in each of these figures is
only valid for an output range selection of 0-to-AV_DD. In 0-to-
V_REF mode, DAC loading will not cause highside voltage drops
as long as the reference voltage remains below the upper trace in
the corresponding figure. For example, if AV_DD = 3 V and V_REF
= 2.5 V, the highside voltage will not be affected by loads less
than 5 mA. But somewhere around 7 mA the upper curve in
Figure 24 drops below 2.5 V (V_REF) indicating that at these
higher currents the output will not be capable of reaching V_REF.
5
DAC LOADED WITH 0FFFH
4
3
2
1
DAC LOADED WITH 0000H
0
0
5
10
15
SOURCE/SINK CURRENT – mA
Figure 23. Source and Sink Current Capability with
V_REF = V_DD = 5 V
REV. 0
–33–