RX113_15 Datasheet, PDF (61/121 Pages) Renesas Technology Corp – Renesas MCUs

RX113 Group
5. Electrical Characteristics
Table 5.11 DC Characteristics (9)
Conditions: VCC = AVCC0 = VCC_USB = 1.8 to 3.6 V, VSS = AVSS0 = VSS_USB = 0 V, T_a = –40 to +105°C
Item
Symbol Min.
Typ.*⁷
Max. Unit
Analog power During A/D conversion (at high-speed conversion)
I_AVCC
—
0.7
1.2 mA
supply current _{During D/A conversion (per channel)}
—
0.4
0.8
Waiting for A/D and D/A conversion (all units)
—
—
0.4 μA
Reference
power supply
current
During A/D conversion (at high-speed conversion)
Waiting for A/D conversion (all units)
During D/A conversion
I_REFH0 —
—
I_REFH
—
25
52 μA
—
60 nA
50
100 μA
Waiting for D/A conversion (all units)
—
—
100 nA
Temperature —
sensor*⁶
I_TEMP
—
75
— μA
Comparator B
operating
current*⁶
Window mode
Comparator high-speed mode
Comparator low-speed mode
I_CMP*⁴ —
—
—
12.5
6.5
1.7
— μA
— μA
— μA
LCD operating External resistance division method*⁸
current*⁶
f_LCD = f_SUB = 128 Hz, 1/3 bias, and 4-time slice
I_LCD1*⁵ —
0.04
— μA
Internal voltage boosting method (VLCD.VLCD = 04) I_LCD2*⁵ —
f_LCD = f_SUB = 128 Hz, 1/3 bias, and 4-time slice
0.85
— μA
Internal voltage boosting method (VLCD.VLCD = 12) I_LCD2*⁵ —
f_LCD = f_SUB = 128 Hz, 1/3 bias, and 4-time slice
1.55
— μA
Capacitor split method
f_LCD = f_SUB = 128 Hz, 1/3 bias, and 4-time slice
I_LCD3*⁵ —
0.20
— μA
USB operating During USB communication operation under the
current*³
following settings and conditions
I_USBH*¹ —
4.3
(VCC)
— mA
 Host controller operation is set to full-speed mode
0.9
Bulk OUT transfer (64 bytes) × 1,
(VCC_USB)*³
bulk IN transfer (64 bytes) × 1
 Connect peripheral devices via a 1-meter USB
cable from the USB port.
During USB communication operation under the
following settings and conditions
I_USBF*¹ —
3.6
(VCC)
— mA
 Function controller operation is set to full-speed
1.1
mode
(VCC_USB)*³
Bulk OUT transfer (64 bytes) × 1,
bulk IN transfer (64 bytes) × 1
 Connect the host device via a 1-meter USB cable
from the USB port.
During suspended state under the following setting
and conditions
I_SUSP*² —
0.35
(VCC)
— μA
 Function controller operation is set to full-speed
170
mode (pull up the USB0_DP pin)
(VCC_USB)*³
 Software standby mode
 Connect the host device via a 1-meter USB cable
from the USB port.
Test
Conditions
Note 1. Current consumed only by the USB module.
Note 2. Includes the current supplied from the pull-up resistor of the USB0_DP pin to the pull-down resistor of the host device, in
addition to the current consumed by this MCU during the suspended state.
Note 3. Current consumed by the power supplies (VCC and USB_VCC).
Note 4. Current consumed only by the comparator B module.
Note 5. Current consumed only by the LCD module. Current when the LCD panel is not connected.
Note 6. Current consumed by the power supply (VCC).
Note 7. When VCC = AVCC0 = VCC_USB = 3.3 V.
Note 8. It does not include the current that flows through external divider resistors.
R01DS0216EJ0102 Rev.1.02
Dec 01, 2014
Page 61 of 121