M16C6K7 Datasheet, PDF (46/285 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

Rev.1.0
Interrupt
Mitsubishi microcomputers
M16C / 6K7 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Table.DD-2 Interrupts assigned to the variable vector tables and addresses of vector tables
Software interrupt number
Software interrupt number 0
Vector table address
Address (L) to address (H)
Interrupt source
+0 to +3 (Note 1)
BRK instruction
Remarks
Cannot be masked by I flag
Software interrupt number 4
Software interrupt number 5
+16 to +19 (Note 1)
+20 to +23 (Note 1)
INT3
Timer B5/INT9 (Note 2)
Software interrupt number 6
+24 to +27 (Note 1) Timer B4
Software interrupt number 7
+28 to +31 (Note 1) Timer B3
Software interrupt number 8
+32 to +35 (Note 1) SI/O4/INT6 (Note 2)
Software interrupt number 9
Software interrupt number 10
Software interrupt number 11
+36 to +39 (Note 1)
+40 to +43 (Note 1)
+44 to +47 (Note 1)
SI/O3/INT5 (Note 2)
Bus collision detection/INT4 ^{(Note 2)}
DMA0/INT8 (Note 3)
Software interrupt number 12
+48 to +51 (Note 1) DMA1/INT7 ^{(Note 3)}
Software interrupt number 13 +52 to +55 (Note 1) Key input interrupt 0
Software interrupt number 14 +56 to +59 (Note 1) A-D
Software interrupt number 15 +60 to +63 (Note 1) UART2 transmit/IBF0 (Note 2)
Software interrupt number 16
Software interrupt number 17
+64 to +67 (Note 1)
+68 to +71 (Note 1)
UART2 receive/IBF1 (Note 2)
UART0 transmit/I²C0 (Note 2)
Software interrupt number 18
Software interrupt number 19
+72 to +75 (Note 1)
+76 to +79 (Note 1)
UART0 receive/SCL0,SDA0/INT11 (Note 3)
UART1 transmit/I²C1 (Note 2)
Software interrupt number 20 +80 to +83 (Note 1) UART1 receive/SCL1,SDA1/INT10 (Note 3)
Software interrupt number 21 +84 to +87 (Note 1) Timer A0/INT8 (Note 3)
Software interrupt number 22 +88 to +91 (Note 1) Timer A1/INT7 (Note 3)
Software interrupt number 23 +92 to +95 (Note 1) Timer A2
Software interrupt number 24 +96 to +99 (Note 1) Timer A3/IBF2
Software interrupt number 25 +100 to +103 (Note 1) Timer A4/IBF3
Software interrupt number 26 +104 to +107 (Note 1) Timer B0/INT11/SCL0,SDA0 (Note 3)
Software interrupt number 27 +108 to +111 (Note 1) Timer B1/INT10/SCL1,SDA1 (Note 3)
Software interrupt number 28 +112 to +115 (Note 1) Timer B2/Key input interrupt 1 (Note 2)
Software interrupt number 29
Software interrupt number 30
+116 to +119 (Note 1)
+120 to +123 (Note 1)
INT0/PS20 (Note 2)
INT1/PS21 (Note 2)
Software interrupt number 31 +124 to +127 (Note 1) INT2/PS22 (Note 2)
Software interrupt number 32
to
Software interrupt number 63
+128 to +131 (Note 1)
to
+252 to +255 (Note 1)
Software interrupt
Cannot be masked by I flag
Note 1: Address relative to address in interrupt table register (INTB).
Note 2: It is selected by interrupt request cause bit.
Note 3: Depend on interrupt event selection bit setting.Please do not set same interrupt
event at the same time.
45