M16C6K7 Datasheet, PDF (243/285 Pages) Renesas Technology Corp – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER

Rev.1.0
Electrical characteristics
Mitsubishi microcomputers
M16C / 6K7 Group
SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER
Table.ZA-4 Electorical characteristice (referenced to Vcc=3.0V,Vss=0V,Ta=25^oC,f(XIN)=8MHz with WAIT)
Symbol
Parameter
Measuring condition
Standard
Unit
Min. Typ. Max.
VOH
High output
P00 to P07, P10 to P17, P20 to P27, P30 to P37, IOH=-1mA
2.5
V
voltage
P40 to P47, P50 to P57, P64 to P67, P86, P87,
P90 to P97, P100 to P107, P110 to P117,
P120 to P127, P140 to P147, P150 to P157,
P160, P161
VOH
High output
XOUT
HIGH POWER
IOH=-0.1mA
2.5
V
voltage
LOWPOWER
IOH=-50µA
2.5
High output
XCOUT
HIGHPOWER
With no load applied
3.0
V
voltage
LOWPOWER
With no load applied
1.6
VOL
Low output
P00 to P07, P10 to P17, P20 to P23, P30 to P37,
voltage
P40 to P47,P50 to P57, P60 to P67, P70 to P77,
P80 to P84, P86, P87, P90 to P97, P100 to P107, IOL=1mA
0.5
V
P110 to P117, P120 to P127, P130 to P137,
P140 to P147, P150 to P157, P160, P161
P24 to P27
VCC=3V, IOL=3mA
0.5
V
VOL
Low output
P140 to P143
HIGH POWER
IOL=3mA
0.5
V
voltage
LOWPOWER
IOL=1mA
0.5
V
VOL
Low output
XOUT
HIGH POWER
IOH=0.1mA
0.5
V
voltage
LOWPOWER
IOH=50µA
0.5
Low output
XCOUT
HIGHPOWER
With no load applied
0
V
VT+VT-
voltage
Hysteresis
LOWPOWER
_______
_________
TA0IN to TA4IN, TB0IN to TB5IN, INT0 to INT11,
__________ ________ ________ ________
ADTRG, CTS0, CTS1, CTS2, CLK0, CLK1,
With no load applied
0
0.2
0.8
VT+VT-
Hysteresis
CLK2, CLK3, CLK4, SIN3, SIN4, RXD0, RXD1,
_______ ________ ________
RXD2, ICCK, NMI, KI00 to KI07
____________
RESET
0.2
1.8
V
IIH
HIGH input
P00 to P07, P10 to P17, P20 to P27, P30 to P37,
current
P40 to P47, P50 to P57, P60 to P67, P70 to P77,
P80 to P87, P90 to P97, P100 to P107,
VI=3V
4.0
µA
P120 to P127, P130 to P137, P140 to P147,
____________
P150 to P157, P160, P161, XIN, RESET, M0, M1
IIL
Low input
P00 to P07, P10 to P17, P20 to P27, P30 to P37,
current
P40 to P47, P50 to P57, P60 to P67, P70 to P77,
P80 to P87, P90 to P97, P100 to P107,
VI=0V
-4.0
µA
P110 to P117, P120 to P127, P130 to P137,
P140 to P147, P150 to P157, P160, P161,
____________
XIN, RESET, M0, M1
R PULLUP Pull-up
P00 to P07, P10 to P17, P20 to P27,
resisitance
P30 to P37, P40 to P47, P50 to P57,
P64 to P67, P86, P87, P90 to P97,
VI=0V
66.0 120.0 500.0
kΩ
P100 to P107, P110 to P117,
P120 to P127, P140 to P147,
P150 to P157, P160, P161
R fXIN
Feedback resistance XIN
3.0
MΩ
R fXCIN
Feedback resistance XCIN
10.0
MΩ
V RAM
RAM retention voltage
When clock is stopped
2.0
V
I CC
When reset, the output pins are opened , the
f(XIN)=8MHZ,Square wave
12.5 24.25
mA
other pins are connected to Vss.
without division
f(XCIN)=32kHZ,Square wave
40.0
µA
Power supply
When operation under RAM
current
f(XCIN)=32kHZ,Square wave When
300.0
µA
operation under Flash memory
f(XCIN)=32kHZ,With WAIT
4.5
µA
oscillation capacity High
(Note1)
f(XCIN)=32kHZ,With WAIT
2.5
µA
oscillation capacity Low
(Note1)
Ta=25°C
3.0
µA
When clock is stopprd
Ta=85°C
60.0
µA
When clock is stopprd
242