M16C63 Datasheet, PDF (104/115 Pages) Renesas Technology Corp – RENESAS MCU

M16C/63 Group
5. Electrical Characteristics
5.4 Electrical Characteristics (V_CC1 = V_CC2 = 1.8 V)
5.4.1 Electrical Characteristics
V_CC1 = V_CC2 = 1.8 V
Table 5.61 Electrical Characteristics (1) ⁽¹⁾
V_CC1 = V_CC2 = 1.8 to 2.7 V, V_SS = 0 V at T_opr = -20 to 85°C/-40 to 85°C, f_(BCLK) = 5 MHz unless otherwise
specified.
Symbol
Parameter
V_OH High
output
P6_0 to P6_7, P7_2 to P7_7,
P8_0 to P8_4, P8_6, P8_7,
voltage P9_0 to P9_7, P10_0 to P10_7
P0_0 to P0_7, P1_0 to P1_7,
P2_0 to P2_7, P3_0 to P3_7,
P4_0 to P4_7, P5_0 to P5_7
V_OH High output voltage XOUT
HIGHPOWER
LOWPOWER
High output voltage XCOUT
V_OL Low output P6_0 to P6_7, P7_0 to P7_7,
voltage P8_0 to P8_7, P9_0 to P9_7,
P10_0 to P10_7
P0_0 to P0_7, P1_0 to P1_7,
P2_0 to P2_7, P3_0 to P3_7,
P4_0 to P4_7, P5_0 to P5_7
V_OL Low output voltage XOUT
HIGHPOWER
LOWPOWER
Low output voltage XCOUT
V_T+-V_T- Hysteresis HOLD, RDY, TA0IN to TA4IN,
TB0IN to TB5IN, INT0 to INT7, NMI,
ADTRG, CTS0 to CTS2, CTS5 to CTS7,
SCL0 to SCL2, SCL5 to SCL7,
SDA0 to SDA2, SDA5 to SDA7,
CLK0 to CLK7, TA0OUT to TA4OUT,
KI0 to KI7, RXD0 to RXD2,
RXD5 to RXD7, SIN3, SIN4, SD, PMC0,
PMC1,
SCLMM, SDAMM, CEC
V_T+-V_T- Hysteresis RESET
I_IH
High input P0_0 to P0_7, P1_0 to P1_7,
current P2_0 to P2_7, P3_0 to P3_7,
P4_0 to P4_7, P5_0 to P5_7,
P6_0 to P6_7, P7_0 to P7_7,
P8_0 to P8_7, P9_0 to P9_7,
P10_0 to P10_7
XIN, RESET, CNVSS, BYTE
Measuring Condition
Standard
Min. Typ.
I_OH = −1 mA
V_CC1 − 0.5
I_OH = −1 mA
V_CC2 − 0.5
I_OH = −0.1 mA
V_CC1 − 0.5
I_OH = −50 μA
V_CC1 − 0.5
With no load applied
1.5
I_OL = 1 mA
I_OL = 1 mA
I_OL = 0.1 mA
I_OL = 50 μA
With no load applied
0
0.02
0.05
V_I = 3 V
Unit
Max.
V_CC1 V
V_CC2
V_CC1 V
V_CC1
V
0.5 V
0.5
0.5 V
0.5
V
0.1 V
0.15 V
2.0 μA
Note:
1. When V_CC1 ≠ V_CC2, refer to 5 V, 3 V, or 1.8 V standard depending on the voltage.
REJ03B0271-0100 Rev.1.00 Sep 15, 2009
Page 104 of 113