PIC18LF2X_13 Datasheet, PDF (438/560 Pages) Microchip Technology – PIC18(L)F2X/45K50 USB Flash MCU Product Brief

PIC18(L)F2X/4XK22
27.6 DC Characteristics: Primary Idle Supply Current, PIC18(L)F2X/4XK22
PIC18LF2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +125°C
PIC18F2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +125°C
Param
No.
Device Characteristics
Typ Max Units
Conditions
D100
D101
Supply Current (IDD)^(1),(2)
0.030 0.050 mA -40°C to +125°C
0.045 0.065 mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
Fosc = 1 MHz
(PRI_IDLE mode,
ECM source)
D102
D103
D104
0.06 0.12
0.08 0.15
0.13 0.20
mA -40°C to +125°C
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 2.3V
VDD = 3.0V
VDD = 5.0V
Fosc = 1 MHz
(PRI_IDLE mode,
ECM source)
D105
D106
0.45 0.8
0.70 1.0
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
Fosc = 20 MHz
(PRI_IDLE mode,
ECH source)
D107
D108
D109
0.55 0.8
0.75 1.0
0.90 1.2
mA -40°C to +125°C
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 2.3V
VDD = 3.0V
VDD = 5.0V
Fosc = 20 MHz
(PRI_IDLE mode,
ECH source)
D110
2.25 3.0
mA -40°C to +125°C
VDD = 3.0V
Fosc = 64 MHz
(PRI_IDLE mode,
ECH source)
D111
D112
2.25 3.0
2.60 3.5
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 3.0V
VDD = 5.0V
Fosc = 64 MHz
(PRI_IDLE mode,
ECH source)
D113
D114
0.35 0.6
0.55 0.8
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
Fosc = 4 MHz
16 MHz Internal
(PRI_IDLE mode,
ECM + PLL source)
D115
D116
D117
0.45 0.6
0.60 0.9
0.70 1.0
mA -40°C to +125°C
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 2.3V
VDD = 3.0V
VDD = 5.0V
Fosc = 4 MHz
16 MHz Internal
(PRI_IDLE mode,
ECM + PLL source)
D118
2.2 3.0 mA -40°C to +125°C VDD = 3.0V Fosc = 16 MHz
64 MHz Internal
(PRI_IDLE mode,
ECH + PLL source)
D119
D120
2.2 3.0 mA -40°C to +125°C VDD = 3.0V Fosc = 16 MHz
2.5 3.5 mA -40°C to +125°C VDD = 5.0V ^{64 MHz Internal}
(PRI_IDLE mode,
ECH + PLL source)
Note 1:
2:
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
Test condition: All Peripheral Module Control bits in PMD0, PMD1 and PMD2 set to ‘1’.
The test conditions for all IDD measurements in active operation mode are:
All I/O pins set as outputs driven to Vss;
MCLR = VDD;
OSC1 = external square wave, from rail-to-rail (PRI_RUN and PRI_IDLE only).
DS41412F-page 438
 2010-2012 Microchip Technology Inc.