PIC18LF2X_13 Datasheet, PDF (437/560 Pages) Microchip Technology – PIC18(L)F2X/45K50 USB Flash MCU Product Brief

PIC18(L)F2X/4XK22
27.5 DC Characteristics: Primary Run Supply Current, PIC18(L)F2X/4XK22
PIC18LF2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +125°C
PIC18F2X/4XK22
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +125°C
Param
No.
Device Characteristics
Typ Max Units
Conditions
D070
D071
Supply Current (IDD)^(1),(2)
0.11 0.20
0.17 0.25
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
FOSC = 1 MHz
(PRI_RUN mode,
ECM source)
D072
D073
D074
0.15 0.25
0.20 0.30
0.25 0.35
mA -40°C to +125°C
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 2.3V
VDD = 3.0V
VDD = 5.0V
FOSC = 1 MHz
(PRI_RUN mode,
ECM source)
D075
D076
1.45 2.0
2.60 3.5
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 1.8V
VDD = 3.0V
FOSC = 20 MHz
(PRI_RUN mode,
ECH source)
D077
D078
D079
1.95 2.5
2.65 3.5
2.95 4.5
mA -40°C to +125°C
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 2.3V
VDD = 3.0V
VDD = 5.0V
FOSC = 20 MHz
(PRI_RUN mode,
ECH source)
D080
7.5 10 mA -40°C to +125°C VDD = 3.0V FOSC = 64 MHz
(PRI_RUN,
ECH oscillator)
D081
D082
7.5 10 mA -40°C to +125°C VDD = 3.0V FOSC = 64 MHz
8.5 11.5 mA -40°C to +125°C VDD = 5.0V ^{(PRI_RUN mode,}
ECH source)
D083
D084
1.0 1.5 mA -40°C to +125°C VDD = 1.8V FOSC = 4 MHz
1.8 3.0 mA -40°C to +125°C VDD = 3.0V ^{16 MHz Internal}
(PRI_RUN mode,
ECM + PLL source)
D085
D086
D087
1.4 2.0
1.85 2.5
2.1 3.0
mA -40°C to +125°C
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 2.3V
VDD = 3.0V
VDD = 5.0V
FOSC = 4 MHz
16 MHz Internal
(PRI_RUN mode,
ECM + PLL source)
D088
6.35 9.0
mA -40°C to +125°C
VDD = 3.0V
FOSC = 16 MHz
64 MHz Internal
(PRI_RUN mode,
ECH + PLL source)
D089
D090
6.35 9.0
7.0 10
mA -40°C to +125°C
mA -40°C to +125°C
VDD = 3.0V
VDD = 5.0V
FOSC = 16 MHz
64 MHz Internal
(PRI_RUN mode,
ECH + PLL source)
Note 1:
2:
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin loading
and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have an impact on
the current consumption.
Test condition: All Peripheral Module Control bits in PMD0, PMD1 and PMD2 set to ‘1’.
The test conditions for all IDD measurements in active operation mode are:
All I/O pins set as outputs driven to Vss;
MCLR = VDD;
OSC1 = external square wave, from rail-to-rail (PRI_RUN and PRI_IDLE only).
 2010-2012 Microchip Technology Inc.
DS41412F-page 437