PIC16F1829LIN Datasheet, PDF (62/74 Pages) Micon Design Technology Corporation – 20-Pin, 8-bit Flash LIN/J2602 Microcontroller

PIC16F1829LIN
10.2 DC Characteristics: PIC16F1829LIN-E (Extended) (Continued)
PIC16F1829LIN
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +125°C for extended
Param.
No.
Symbol
Device
Characteristics
Min. Typ† Max. Units
VDD
Conditions
Note
D014
Supply Current (IDD)^{(2, 3)}
—
192
250
A
—
336
430
A
1.8 FOSC = 4 MHz
3.0 ^{EC Oscillator}
Medium-Power mode
D014
—
210
275
A
—
356
450
A
—
430
650
A
1.8 FOSC = 4 MHz
3.0 ^{EC Oscillator}
Medium-Power mode
5.0
D015
D015
—
6.5
18
A
1.8 FOSC = 31 kHz
—
9.0
20
A
3.0 ^LFINTOSC
—
20
60
A
1.8 FOSC = 31 kHz
—
25
65
A
3.0 ^LFINTOSC
D016
D016
—
27
70
A
—
110
170
A
—
130
200
A
—
125
180
A
—
155
250
A
5.0
1.8 FOSC = 500 kHz
3.0 ^MFINTOSC
1.8 FOSC = 500 kHz
3.0 ^MFINTOSC
—
160
280
A
5.0
D017*
—
0.6
0.85
mA
1.8 FOSC = 8 MHz
—
0.9
1.25
mA
3.0 ^HFINTOSC
D017*
—
0.6
0.85
mA
—
0.96 _1.35
mA
1.8 FOSC = 8 MHz
3.0 ^HFINTOSC
—
1.03 1.55
mA
5.0
D018
—
0.9
1.2
mA
1.8 FOSC = 16 MHz
—
1.4
1.95
mA
3.0 ^HFINTOSC
D018
—
0.92
1.2
mA
1.8 FOSC = 16 MHz
—
1.49
1.9
mA
3.0 ^HFINTOSC
—
1.58
2.4
mA
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
TBD = To be determined
Note 1:
2:
3:
4:
5:
6:
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit.
Maximum values should be used when calculating total current consumption.
The test conditions for all IDD measurements in active Operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
8 MHz internal RC oscillator with 4x PLL enabled.
8 MHz crystal oscillator with 4x PLL enabled.
For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k.
DS41673A-page 62
Preliminary
 2012 Microchip Technology Inc.