PIC16F1829LIN Datasheet, PDF (1/74 Pages) Micon Design Technology Corporation – 20-Pin, 8-bit Flash LIN/J2602 Microcontroller

PIC16F1829LIN
20-Pin, 8-bit Flash LIN/J2602 Microcontroller
Cross-Referenced Material:
This data sheet refers heavily on the following
Microchip data sheets:
• “PIC16(L)F1825/1829 Data Sheet” (DS41440)
• “MCP2021A/2A, LIN Transceiver with Voltage
Regulator Data Sheet” (DS22298)
Please have these documents available when reading
this device specification. Only deviations from the data
sheets listed above will be noted.
High-Performance RISC CPU:
• Only 49 Instructions to Learn:
- All single-cycle instructions except branches
• Operating Speed:
- DC – 32 MHz oscillator/clock input
- DC – 125 ns instruction cycle
• 16 Kbytes Linear Program Memory Addressing
• 1024 bytes Linear Data Memory Addressing
• Interrupt Capability with Automatic Context
Saving
• 16-Level Deep Hardware Stack with Optional
Overflow/Underflow Reset
• Direct, Indirect and Relative Addressing modes:
- Two full 16-bit File Select Registers (FSRs)
- FSRs can read Program and Data memory
Flexible Oscillator Structure:
• Precision 32 MHz Internal Oscillator Block:
- Factory calibrated to ± 1%, typical
- Software selectable frequencies range of
31 kHz to 32 MHz
• Four Crystal modes up to 32 MHz
• Three External Clock modes up to 32 MHz
• 4x Phase Lock Loop (PLL)
• Fail-Safe Clock Monitor:
- Allows for safe shutdown if peripheral clock
stops
• Two-Speed Oscillator Start-up
• Reference Clock Module:
- Programmable clock output frequency and
duty-cycle
Special Microcontroller Features:
• Self-Programmable under Software Control
• Power-on Reset (POR), Power-up Timer (PWRT)
and Oscillator Start-up Timer (OST)
• Programmable Brown-out Reset (BOR)
• Extended Watchdog Timer (WDT)
• In-Circuit Serial Programming™ (ICSP™) via
Two Pins
• In-Circuit Debug (ICD) via Two Pins
• Enhanced Low-Voltage Programming (LVP)
• Operating Voltage Range of the Microcontroller:
- 2.3V-5.5V
• Programmable Code Protection
• Power-Saving Sleep mode
Analog Features:
• Analog-to-Digital Converter (ADC) Module:
- 10-bit resolution
- Nine analog input channels
- Conversion available during Sleep
• Analog Comparator Module:
- Two rail-to-rail analog comparators
- Power mode control
- Software controllable hysteresis
• Voltage Reference Module:
- Fixed Voltage Reference (FVR) with multiple
output levels
- 5-bit rail-to-rail resistive DAC with positive
and negative reference selection
Peripheral Features:
• 12 Digital I/O Pins and one Input-only Pin:
- High current sink/source 25 mA/25 mA
- Individually programmable weak pull-ups
- Individually programmable
Interrupt-on-change pins
• Timer0: 8-Bit Timer/Counter with 8-Bit Prescaler
• Enhanced Timer1:
- 16-bit timer/counter with prescaler
- External Gate Input mode
- Dedicated, low-power 32 kHz oscillator driver
• Three Timer2 types: 8-Bit Timer/Counter with 8-Bit
Period Register, Prescaler and Postscaler
• Two Capture, Compare, PWM (CCP) Modules (one
is internal only)
• Two Enhanced CCP (ECCP) Modules:
- Software-selectable time bases
- Auto-shutdown and auto-restart
- PWM steering
 2012 Microchip Technology Inc.
Preliminary
DS41673A-page 1