SAP5SD-A-G1-T Datasheet, PDF (20/63 Pages) List of Unclassifed Manufacturers – Universal Actuator-Sensor Interface IC

SAP5S / SAP51
Universal Actuator-Sensor Interface IC
Instruction
Data Exchange
MNE
DEXG
Write Parameter
WPAR
Address Assignment ADRA
Write Extented ID
Code_1
WID1
Delete Address
DELA
Reset Slave
Read IO
Configuration
Read ID Code
RES
RDIO
RDID
Read ID Code_1
RID1
Read ID Code_2
RID2
Read Status
RDST
Broadcast (Reset) BR01
Table 6: SAP5 Master Calls and Related Slave Responses
Master Request
ST CB A4 A3 A2 A1 A0 I4 I3 I2 I1 I0 PB EB
0
0
A4 A3 A2 A1 A0
0
D3
~Sel
D2
D1
D0
PB
1
0
0
A4 A3 A2 A1 A0
1
P3
~Sel
P2
P1
P0
PB
1
0 0 0 0 0 0 0 A4 A3 A2 A1 A0 PB 1
0 1 0 0 0 0 0 0 ID3 ID2 ID1 ID0 PB 1
0 1 A4 A3 A2 A1 A0 0 0 Sel 0 0 0 PB 1
0
1
A4 A3 A2 A1 A0
1
1
~Sel
1
0
0 PB 1
0
1
A4 A3 A2 A1 A0
1
0
Sel
0
0
0 PB 1
0
1
A4 A3 A2 A1 A0
1
0
Sel
0
0
1 PB 1
0
1
A4 A3 A2 A1 A0
1
0
Sel
0
1
0 PB 1
0
1
A4 A3 A2 A1 A0
1
0
Sel
0
1
1 PB 1
0
1
A4 A3 A2 A1 A0
1
1
~Sel
1
1
0 PB 1
01111111010111
Slave Response
SB I3 I2 I1 I0 PB EB
0 D3 D2 D1 D0 PB 1
0 P3 P2 P1 P0 PB 1
0011001
0000001
0000001
0011001
0 IO3 IO2 IO1 IO0 PB 1
0 ID3 ID2 ID1 ID0 PB 1
0 ID3 ID2 ID1 ID0 PB 1
0 ID3 ID2 ID1 ID0 PB 1
0 S3 S2 S1 S0 PB 1
--- no slave response ---
NOTE: In extended address mode the "Select Bit" defines whether the A-Slave or B-Slave is being addressed. Dependent on the type of master call the I3 bit
carries the select bit information (Sel) or the inverted select bit information (~Sel). The extended address mode can not be activated, as long as the E²PROM
flag Lock_EE_PRG is at logic LOW level. Refer to chapter 3.3 on page 25 for programming the Lock_EE_PRG flag.
Data Sheet
July 17, 2012
© 2012 Zentrum Mikroelektronik Dresden AG — Rev. 3.1
All rights reserved. The material contained herein may not be reproduced, adapted, merged, translated, stored, or used without
the prior written consent of the copyright owner. The information furnished in this publication is PRELIMINARY and subject to
changes without notice.
20 of 62