DS90UR910Q_14 Datasheet, PDF (6/31 Pages) Texas Instruments – 10 - 75 MHz 24-bit Color FPD-Link II to CSI-2 Converter

DS90UR910Q
SNLS414C – JUNE 2012 – REVISED MAY 2013
www.ti.com
DC ELECTRICAL CHARACTERISTICS^(1)(2)(3)
Over recommended operating supply and temperature ranges unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ
Max Units
3.3V I/O LVCMOS DC SPECIFICATIONS – V_DDIO = 3.0 to 3.6V (BISTEN, LOCK, PASS, PDB, EQ[3:1], ID[1:0], CONFIG[1:0], GPIO)
V_IH
High Level Input Voltage
V_IN = 3.0V to 3.6V
2.2
V_DDIO
V
V_IL
Low Level Input Voltage
V_IN = 3.0V to 3.6V
GND
0.8
V
I_IN
Input Current
V_IN = 0V or V_DDIO
−15
+15 μA
V_OH
High Level Output Voltage
I_OH = −2 mA
2.4
V_DDIO
V
V_OL
Low Level Output Voltage
I_OL = +2 mA
GND
0.4
V
I_OZ
TRI-STATE Output Current
PDB = 0V
−15
+15
uA
1.8V I/O LVCMOS DC SPECIFICATIONS – V_DDIO = 1.71 to 1.89V (BISTEN, LOCK, PASS, PDB, EQ[3:1], ID[1:0], CONFIG[1:0], GPIO)
V_IH
High Level Input Voltage
V_IN = 1.71V to 1.89V
0.65*
V_DDIO
V_DDIO
V
V_IL
Low Level Input Voltage
V_IN = 1.71V to 1.89V
GND
0.35*
V_DDIO
V
I_IN
Input Current
V_IN = 0V or V_DDIO
−15
+15 μA
V_OH
High Level Output Voltage
I_OH = −2 mA
V_DDIO
−0.45
V_DDIO
V
V_OL
Low Level Output Voltage
I_OZ
TRI-STATE^® Output Current
SUPPLY CURRENT
I_OL = +2 mA
PDB = 0V
GND
−15
0.45
V
+15 µA
I_DD1
Supply current
Supply current drawn from
1.8V rail (V_DDL, V_DDP, V_DDA)
Checker Board Pattern
V_DDL, V_DDP, V_DDA
= 1.89V
f = 75 MHz
(900 Mbps)
88
95
mA
V_DDL, V_DDP, V_DDA
= 1.89V
f = 10 MHz
38
mA
(120 Mbps)
I_DDTX1
Supply current drawn at
V_DDCSI
Checker Board Pattern
V_DDCSI = 1.89V
f = 75 MHz
(900 Mbps)
50
65
mA
V_DDCSI = 1.89V
f = 10 MHz
(120 Mbps)
22
mA
I_DDIO1
Supply current drawn at V_DDIO V_DDIO = 1.89V
Checker Board Pattern
f = 75 MHz
(900 Mbps)
10
mA
V_DDIO = 3.6V
f = 75 MHz
(900 Mbps)
15
mA
(1) Current into device pins is defined as positive. Current out of a device pin is defined as negative. Voltages are referenced to ground
except VOD, ΔVOD, VTH and VTL which are differential voltages.
(2) Typical values represent most likely parametric norms at V_DD = 3.3V, Ta = +25 degC, and at the Recommended Operation Conditions at
the time of product characterization and are not ensured.
(3) The Electrical Characteristics tables list ensured specifications under the listed Recommended Operating Conditions except as
otherwise modified or specified by the Electrical Characteristics Conditions and/or Notes. Typical specifications are estimations only and
are not ensured.
6
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated
Product Folder Links: DS90UR910Q