CC430F5125 Datasheet, PDF (51/118 Pages) Texas Instruments – MSP430 SoC With RF Core

www.ti.com
ECCN 5E002 TSPA - Technology / Software Publicly Available
CC430F614x
CC430F514x
CC430F512x
SLAS555A – NOVEMBER 2012 – REVISED FEBRUARY 2013
DCO Frequency
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
f_DCO(0,0)
f_DCO(0,31)
f_DCO(1,0)
f_DCO(1,31)
f_DCO(2,0)
f_DCO(2,31)
f_DCO(3,0)
f_DCO(3,31)
f_DCO(4,0)
f_DCO(4,31)
f_DCO(5,0)
f_DCO(5,31)
f_DCO(6,0)
f_DCO(6,31)
f_DCO(7,0)
f_DCO(7,31)
S_DCORSEL
PARAMETER
DCO frequency (0, 0)⁽¹⁾
DCO frequency (0, 31)⁽¹⁾
DCO frequency (1, 0)⁽¹⁾
DCO frequency (1, 31)⁽¹⁾
DCO frequency (2, 0)⁽¹⁾
DCO frequency (2, 31)⁽¹⁾
DCO frequency (3, 0)⁽¹⁾
DCO frequency (3, 31)⁽¹⁾
DCO frequency (4, 0)⁽¹⁾
DCO frequency (4, 31)⁽¹⁾
DCO frequency (5, 0)⁽¹⁾
DCO frequency (5, 31)⁽¹⁾
DCO frequency (6, 0)⁽¹⁾
DCO frequency (6, 31)⁽¹⁾
DCO frequency (7, 0)⁽¹⁾
DCO frequency (7, 31)⁽¹⁾
Frequency step between range
DCORSEL and DCORSEL + 1
TEST CONDITIONS
DCORSELx = 0, DCOx = 0, MODx = 0
DCORSELx = 0, DCOx = 31, MODx = 0
DCORSELx = 1, DCOx = 0, MODx = 0
DCORSELx = 1, DCOx = 31, MODx = 0
DCORSELx = 2, DCOx = 0, MODx = 0
DCORSELx = 2, DCOx = 31, MODx = 0
DCORSELx = 3, DCOx = 0, MODx = 0
DCORSELx = 3, DCOx = 31, MODx = 0
DCORSELx = 4, DCOx = 0, MODx = 0
DCORSELx = 4, DCOx = 31, MODx = 0
DCORSELx = 5, DCOx = 0, MODx = 0
DCORSELx = 5, DCOx = 31, MODx = 0
DCORSELx = 6, DCOx = 0, MODx = 0
DCORSELx = 6, DCOx = 31, MODx = 0
DCORSELx = 7, DCOx = 0, MODx = 0
DCORSELx = 7, DCOx = 31, MODx = 0
S_RSEL = f_{DCO(DCORSEL+1,DCO)}/f_{DCO(DCORSEL,DCO)}
MIN TYP MAX UNIT
0.07
0.20 MHz
0.70
1.70 MHz
0.15
0.36 MHz
1.47
3.45 MHz
0.32
0.75 MHz
3.17
7.38 MHz
0.64
1.51 MHz
6.07
14.0 MHz
1.3
3.2 MHz
12.3
28.2 MHz
2.5
6.0 MHz
23.7
54.1 MHz
4.6
10.7 MHz
39.0
88.0 MHz
8.5
19.6 MHz
60
135 MHz
1.2
2.3 ratio
S_DCO
Frequency step between tap
DCO and DCO + 1
S_DCO = f_{DCO(DCORSEL,DCO+1)}/f_{DCO(DCORSEL,DCO)}
1.02
1.12 ratio
Duty cycle
Measured at SMCLK
40
50
60 %
df_DCO/dT
df_DCO/dV_CC
DCO frequency temperature drift f_DCO = 1 MHz
DCO frequency voltage drift
f_DCO = 1 MHz
0.1
%/°C
1.9
%/V
(1) When selecting the proper DCO frequency range (DCORSELx), the target DCO frequency, f_DCO, should be set to reside within the
range of f_{DCO(n, 0),MAX} ≤ f_DCO ≤ f_{DCO(n, 31),MIN}, where f_{DCO(n, 0),MAX} represents the maximum frequency specified for the DCO frequency,
range n, tap 0 (DCOx = 0) and f_{DCO(n,31),MIN} represents the minimum frequency specified for the DCO frequency, range n, tap 31
(DCOx = 31). This ensures that the target DCO frequency resides within the range selected. It should also be noted that if the actual
f_DCO frequency for the selected range causes the FLL or the application to select tap 0 or 31, the DCO fault flag is set to report that the
selected range is at its minimum or maximum tap setting.
Typical DCO Frequency, V_CC = 3.0 V, T_A = 25°C
100
10
DCOx = 31
1
DCOx = 0
0.1
0
1
2
3
4
5
6
7
DCORSEL
Figure 16. Typical DCO frequency
Copyright © 2012–2013, Texas Instruments Incorporated
Submit Documentation Feedback
51