CC430F5125 Datasheet, PDF (46/118 Pages) Texas Instruments – MSP430 SoC With RF Core

CC430F614x
CC430F514x
CC430F512x
ECCN 5E002 TSPA - Technology / Software Publicly Available
SLAS555A – NOVEMBER 2012 – REVISED FEBRUARY 2013
www.ti.com
Digital Outputs
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)
PARAMETER
TEST CONDITIONS
V_OH
High-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OHmax) = -1 mA, PxDS.y = 0⁽²⁾
V_CC
1.8 V
MIN
V_CC - 0.25
MAX UNIT
V_CC V
V_OH
High-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OHmax) = -3 mA, PxDS.y = 0⁽³⁾
1.8 V
V_CC - 0.60
V_CC V
V_OH
High-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OHmax) = -2 mA, PxDS.y = 0⁽²⁾
3.0 V
V_CC - 0.25
V_CC V
V_OH
High-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OHmax) = -6 mA, PxDS.y = 0⁽³⁾
3.0 V
V_CC - 0.60
V_CC V
V_OL
Low-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OLmax) = 1 mA, PxDS.y = 0⁽²⁾
1.8 V
V_SS V_SS + 0.25 V
V_OL
Low-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OLmax) = 3 mA, PxDS.y = 0⁽³⁾
1.8 V
V_SS V_SS + 0.60 V
V_OL
Low-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OLmax) = 2 mA, PxDS.y = 0⁽²⁾
3.0 V
V_SS V_SS + 0.25 V
V_OL
Low-level output voltage,
Reduced Drive Strength⁽¹⁾
I_(OLmax) = 6 mA, PxDS.y = 0⁽³⁾
3.0 V
V_SS V_SS + 0.60 V
V_OH
High-level output voltage,
Full Drive Strength
I_(OHmax) = -3 mA, PxDS.y = 1⁽²⁾
1.8 V
V_CC - 0.25
V_CC V
V_OH
High-level output voltage,
Full Drive Strength
I_(OHmax) = -10 mA, PxDS.y = 1⁽³⁾
1.8 V
V_CC - 0.60
V_CC V
V_OH
High-level output voltage,
Full Drive Strength
I_(OHmax) = -5 mA, PxDS.y = 1⁽²⁾
3V
V_CC - 0.25
V_CC V
V_OH
High-level output voltage,
Full Drive Strength
I_(OHmax) = -15 mA, PxDS.y = 1⁽³⁾
3V
V_CC - 0.60
V_CC V
V_OL
Low-level output voltage,
Full Drive Strength
I_(OLmax) = 3 mA, PxDS.y = 1⁽²⁾
1.8 V
V_SS V_SS + 0.25 V
V_OL
Low-level output voltage,
Full Drive Strength
I_(OLmax) = 10 mA, PxDS.y = 1⁽³⁾
1.8 V
V_SS V_SS + 0.60 V
V_OL
Low-level output voltage,
Full Drive Strength
I_(OLmax) = 5 mA, PxDS.y = 1⁽²⁾
3V
V_SS V_SS + 0.25 V
V_OL
Low-level output voltage,
Full Drive Strength
I_(OLmax) = 15 mA, PxDS.y = 1⁽³⁾
3V
V_SS V_SS + 0.60 V
f_Px.y
Port output frequency
(with load)
C_L = 20 pF, R_L ⁽⁴⁾⁽⁵⁾
V_CC = 1.8 V,
PMMCOREVx = 0
V_CC = 3 V,
PMMCOREVx = 2
16
MHz
25
f_{Port_CLK} Clock output frequency
C_L = 20 pF⁽⁵⁾
V_CC = 1.8 V,
PMMCOREVx = 0
V_CC = 3 V,
PMMCOREVx = 2
16
MHz
25
(1) Selecting reduced drive strength may reduce EMI.
(2) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined should not exceed ±48 mA to hold the maximum voltage drop
specified.
(3) The maximum total current, I_(OHmax) and I_(OLmax), for all outputs combined should not exceed ±100 mA to hold the maximum voltage
drop specified.
(4) A resistive divider with 2 × R1 between V_CC and V_SS is used as load. The output is connected to the center tap of the divider. For full
drive strength, R1 = 550 Ω. For reduced drive strength, R1 = 1.6 kΩ. C_L = 20 pF is connected to the output to V_SS.
(5) The output voltage reaches at least 10% and 90% V_CC at the specified toggle frequency.
46
Submit Documentation Feedback
Copyright © 2012–2013, Texas Instruments Incorporated