CC3200MOD_15 Datasheet, PDF (20/66 Pages) Texas Instruments – CC3200MOD SimpleLink™ Wi-Fi® and Internet-of-Things Module Solution, a Single-Chip Wireless MCU

CC3200MOD
SWRS166 – DECEMBER 2014
www.ti.com
Pin
GPIO_30
GPIO_31
GPIO_0
GPIO_1
GPIO_2
GPIO_3
GPIO_4
GPIO_5
GPIO_6
GPIO_7
Table 3-3. Recommended Pin Multiplexing Configurations
CC3200 Recommended Pinout Grouping Use – Examples⁽¹⁾
Home
Wifi Audio ++ Sensor-Tag
Security High- Industrial
end Toys
Home
Security Toys
Wifi Audio ++
Industrial
WiFi Remote
w/ 7x7
keypad and
audio
Sensor Door-
Lock Fire-
Alarm Toys
w/o Cam
Industrial
Home
Appliances
Industrial
Home
Appliances
Smart-Plug
Industrial
Home
Appliances"
GPIOs
External 32 External 32
kHz ⁽²⁾
kHz ⁽²⁾
External
TCXO 40
MHZ (-40 to
+85°C)
Cam + I2S
(Tx or Rx) +
I2C + SPI +
SWD +
UART-Tx +
(App Logger)
2 GPIO +
1PWM + *4
overlaid
wakeup from
Hib
I2S (Tx & Rx) I2S (Tx & Rx) Cam + I2S
+ 1 Ch ADC + + 2 Ch ADC + (Tx or Rx) +
1x 4wire
2wire UART + I2C + SWD +
UART + 1x SPI + I2C + UART-Tx +
2wire UART + SWD + 2
(App Logger)
1bit SD Card PMW + 6
4 GPIO +
+ SPI + I2C + GPIO + 3
1PWM + *4
SWD + 3
GPIO with overlaid
GPIO + 1
Wake-From- wakeup from
PWM + 1
Hib
HIB
GPIO with
Wake-From-
Hib
I2S (Tx & Rx) I2S (Tx & Rx) I2S (Tx or Rx) 4 Ch ADC + 3 Ch ADC + 2 Ch ADC +
+ 1 Ch ADC + + 1 Ch ADC + + 2 Ch ADC + 1x 4wire
2wire UART + 2wire UART +
2x 2wire
UART (Tx
2 wire UART UART + 1x SPI + I2C + I2C + SWD +
UART + 1bit Only) I2C + + SPI + I2C + 2wire UART + SWD + 3
3 PWM + 11
SD Card + SWD + 15 3 PMW + 3 SPI + I2C + PWM + 9
GPIO + 5
SPI + I2C + GPIO + 1
GPIO with SWD + 1
GPIO + 2
GPIO with
SWD + 4
PWM + 1
Wake-From- PWM + 6
GPIO with Wake-From-
GPIO + 1
GPIO with
Hib + 5 GPIO GPIO + 1
Wake-From- Hib
PWM + 1
Wake-From- SWD +
GPIO with
Hib
GPIO with Hib
Wake-From-
Wake-From-
Hib Enable
Hib
for Ext 40
MHz TCXO
Pinout #11 Pinout #10 Pinout #9
Pinout #8
Pinout #7
Pinout #6
Pinout #5
Pinout #4
Pinout #3
Pinout #2
Pinout #1
GSPI-MISO MCASP-
ACLKX
MCASP-
ACLKX
GPIO_30
GPIO_30
GPIO_30
GPIO_30
UART0-TX GPIO_30
UART0-TX GPIO_30
GSPI-CLK McASP-AFSX McASP-D0 GPIO_31
McASP-AFSX McASP-AFSX McASP-AFSX UART0-RX GPIO_31
UART0-RX GPIO_31
GSPI-CS
McASP-D1
(Rx)
McASP-D1
McASP-D1
McASP-D1
McASP-D1
McASP-D1
UART0-CTS GPIO_0
GPIO_0
GPIO_0
pCLK
(PIXCLK)
UART0-TX UART0-TX PIXCLK
UART0-TX UART0-TX UART0-TX GPIO-1
UART0-TX GPIO_1
GPIO_1
(wake) GPIO2 UART0-RX UART0-RX (wake) GPIO2 UART0-RX GPIO_2
UART0-RX ADC-0
UART0-RX
(wake)
GPIO_2
(wake)
GPIO_2
pDATA7 (D3) UART1-TX ADC-CH1
pDATA7 (D3) UART1-TX GPIO_3
ADC-1
ADC-1
ADC-1
ADC-1
GPIO_3
pDATA6 (D2) UART1-RX
(wake)
GPIO_4
pDATA6 (D2) UART1-RX GPIO_4
(wake)
GPIO_4
ADC-2
ADC-2
(wake)
GPIO_4
(wake)
GPIO_4
pDATA5 (D1) ADC-3
ADC-3
pDATA5 (D1) ADC-3
ADC-3
ADC-3
ADC-3
ADC-3
ADC-3
GPIO_5
pDATA4 (D0) UART1-CTS GPIO_6
pDATA4 (D0) GPIO_6
GPIO_6
GPIO_6
UART0-RTS GPIO_6
GPIO_6
GPIO_6
McASP-
ACLKX
UART1-RTS GPIO_7
McASP-
ACLKX
McASP-
ACLKX
McASP-
ACLKX
McASP-
ACLKX
GPIO_7
GPIO_7
GPIO_7
GPIO_7
(1) Pins marked "wake" can be configured to wake up the chip from HIBERNATE or LPDS state. In the current silicon revision, any wake pin can trigger wake up from HIBERNATE. The
wakeup monitor in the hibernate control module logically ORs these pins applying a selection mask. However, wakeup from LPDS state can be triggered only by one of the wakeup pins
that can be configured before entering LPDS. The core digital wakeup monitor use a mux to select one of these pins to monitor.
(2) The device supports the feeding of an external 32.768-kHz clock. This configuration frees one pin (32K_XTAL_N) to use in output-only mode with a 100K pullup.
20
Terminal Configuration and Functions
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated