CC3200MOD_15 Datasheet, PDF (19/66 Pages) Texas Instruments – CC3200MOD SimpleLink™ Wi-Fi® and Internet-of-Things Module Solution, a Single-Chip Wireless MCU

www.ti.com
CC3200MOD
SWRS166 – DECEMBER 2014
Table 3-2. Pin Multiplexing (continued)
Pin Alias
General Pin Attributes
Use Select as Config
Wakeup
Addl
Source Analog
Mux
Muxed
with
JTAG
Dig. Pin Mux Config
Reg
Dig. Pin
Mux
Config
Mode
Value
Function
Signal Name
Signal
Description
Signal
Direction
Pad States
LPDS⁽¹⁾ Hib⁽²⁾ nRESET = 0
0
GPIO9
General-Purpose
I/O
I/O
GPIO9
I/O
No
3
No
No
GPIO_PAD_CONFIG_9
(0x4402 E0C4)
6
GT_PWM05
SDCARD_
DATA0
Pulse Width
Modulated O/P
SD Cad Data
O
I/O
Hi-Z
Hi-Z
Hi-Z
7
McAXR0
I2S Audio Port
I/O
Data (Rx/Tx)
12
GT_CCP00 Timer Capture Port
I
(1) LPDS mode: The state of unused GPIOs in LPDS is input with 500-kΩ pulldown. For all used GPIOs , the user can enable internal pulls, which would hold them in a valid state.
(2) Hibernate mode: The CC3200 device leaves the digital pins in a Hi-Z state without any internal pulls when the device enters hibernate state. This can cause glitches on output lines unless
held at valid levels by external resistors.
(3) To minimize leakage in some serial flash vendors during LPDS, TI recommends the user application always enable internal weak pulldowns on FLASH_SPI_DATA and FLASH_SPI_CLK
pins.
(4) This pin has dual functions: as a SOP[2] (device operation mode), and as an external TCXO enable. As a TXCO enable, the pin is an output on power up and driven logic high. During
hibernate low-power mode, the pin is in a high impedance state but pulled down for SOP mode to disable TCXO. Because of SOP functionality, the pin must be used as output only.
(5) For details on proper use, see Drive Strength and Reset States for Analog-Digital Multiplexed Pins.
(6) This pin is one of three that must have a passive pullup or pulldown resistor on board to configure the chip hardware power-up mode. For this reason, the pin must be output only when
used for digital functions.
(7) This pin is reserved for WLAN antenna selection, controlling an external RF switch that multiplexes the RF pin of the CC3200 module between two antennas. These pins should not be
used for other functionalities in general.
(8) Device firmware automatically enables the digital path during ROM boot.
(9) This pin is shared by the ADC inputs and digital I/O pad cells. Important: The ADC inputs are tolerant up to 1.8 V. On the other hand, the digital pads can tolerate up to 3.6 V. Hence, care
must be taken to prevent accidental damage to the ADC inputs. TI recommends that the output buffer(s) of the digital I/Os corresponding to the desired ADC channel be disabled first (that
is, converted to high-impedance state), and thereafter the respective pass switches (S7, S8, S9, S10) should be enabled (see Drive Strength and Reset States for Analog-Digital
Multiplexed Pins).
(10) Requires user configuration to enable the ADC channel analog switch. (The switch is off by default.) The digital I/O is always connected and must be made Hi-Z before enabling the ADC
switch.
3.4 Recommended Pin Multiplexing Configurations
Table 3-3 lists the recommended pin multiplexing configurations.
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
Terminal Configuration and Functions
19