SLDS145B Datasheet, PDF (1/29 Pages) Texas Instruments – TFP410 TI PanelBus DIGITAL TRANSMITTER

TFP410
TI PanelBus™ DIGITAL TRANSMITTER
D Digital Visual Interface (DVI) Compliant¹
D Supports Pixel Rates Up to 165 MHz
(Including 1080p and WUXGA at 60Hz)
D Universal Graphics Controller Interface
− 12-Bit, Dual-Edge and 24-Bit,
Single-Edge Input Modes
− Adjustable 1.1 V to 1.8 V and Standard
3.3 V CMOS Input Signal Levels
− Fully Differential and Single-Ended Input
Clocking Modes
− Standard Intel 12-Bit Digital Video Port
Compatible as on Intel™ 81x Chipsets
D Enhanced PLL Noise Immunity
− On-Chip Regulators and Bypass
Capacitors for Reducing System Costs
SLDS145B − OCTOBER 2001 − REVISED MAY 2011
D Enhanced Jitter Performance
− No HSYNC Jitter Anomaly
− Negligible Data-Dependent Jitter
D Programmable Using I²C Serial Interface
D Monitor Detection Through Hot-Plug and
Receiver Detection
D Single 3.3-V Supply Operation
D 64-Pin TQFP Using TI’s PowerPAD™
Package
D TI’s Advanced 0.18 μm EPIC-5™ CMOS
Process Technology
D Pin Compatible With SiI164 DVI Transmitter
description
The TFP410 is a Texas Instruments PanelBus flat panel display product, part of a comprehensive family of
end-to-end DVI 1.0-compliant solutions, targeted at the PC and consumer electronics industry.
The TFP410 provides a universal interface to allow a glue-less connection to most commonly available graphics
controllers. Some of the advantages of this universal interface include selectable bus widths, adjustable signal
levels, and differential and single-ended clocking. The adjustable 1.1-V to 1.8-V digital interface provides a
low-EMI, high-speed bus that connects seamlessly with 12-bit or 24-bit interfaces. The DVI interface supports
flat panel display resolutions up to UXGA at 165 MHz in 24-bit true color pixel format.
The TFP410 combines PanelBus circuit innovation with TI’s advanced 0.18 μm EPIC-5 CMOS process
technology and TI’s ultralow ground inductance PowerPAD package. The result is a compact 64-pin TQFP
package providing a reliable, low-current, low-noise, high-speed digital interface solution.
This device contains circuits to protect its inputs and outputs against damage due to high static voltages or electrostatic fields. These
circuits have been qualified to protect this device against electrostatic discharges (ESD) of up to 2 kV according to MIL-STD-883C,
Method 3015; however, it is advised that precautions be taken to avoid application of any voltage higher than maximum-rated
voltages to these high-impedance circuits. During storage or handling, the device leads should be shorted together or the device
should be placed in conductive foam. In a circuit, unused inputs should always be connected to an appropriated logic voltage level,
preferably either V_CC or ground. Specific guidelines for handling devices of this type are contained in the publication Guidelines for
Handling Electrostatic-Discharge-Sensitive (ESDS) Devices and Assemblies available from Texas Instruments.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Footnote:
1. The digital visual interface (DVI) specification is an industry standard developed by the digital display working group (DDWG) for high-speed
digital connection to digital displays and has been adopted by industry-leading PC and consumer electronics manufacturers. The TFP410
is compliant to the DVI Revision 1.0 specification.
PanelBus, PowerPAD, and EPIC-5 are trademarks of Texas Instruments.
VESA is a trademark of Video Electronics Standards Association.
Intel is a trademark of Intel Corporation.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
Copyright © 2002 − 2011, Texas Instruments Incorporated
• POST OFFICE BOX 655303 DALLAS, TEXAS 75265
1