HYB18T1G400BF_07 Datasheet, PDF (42/74 Pages) Qimonda AG – 1-Gbit Double-Data-Rate-Two SDRAM

Internet Data Sheet
HY[B/I]18T1G[40/80/16]0B[C/F](L/V)
1-Gbit Double-Data-Rate-Two SDRAM
6
Currents Measurement Conditions
This chapter describes the current measurement specifications and conditions.
TABLE 46
I_DD Measurement Conditions
Parameter
Symbol Note
Operating Current - One bank Active - Precharge
I_DD0
t_CK = t_CK(IDD), t_RC = t_RC(IDD), t_RAS = t_RAS.MIN(IDD), CKE is HIGH, CS is HIGH between valid commands.
Address and control inputs are switching; Databus inputs are switching.
Operating Current - One bank Active - Read - Precharge
I_DD1
I_OUT = 0 mA, BL = 4, t_CK = t_CK(IDD), t_RC = t_RC(IDD), t_RAS = t_RAS.MIN(IDD), t_RCD = t_RCD(IDD), AL = 0, CL = CL(IDD);
CKE is HIGH, CS is HIGH between valid commands. Address and control inputs are switching; Databus
inputs are switching.
Precharge Power-Down Current
All banks idle; CKE is LOW; t_CK = t_CK(IDD);Other control and address inputs are stable; Data bus inputs are
floating_.
Precharge Standby Current
All banks idle; CS is HIGH; CKE is HIGH; t_CK = t_CK(IDD); Other control and address inputs are switching,
Data bus inputs are switching_.
Precharge Quiet Standby Current
All banks idle; CS is HIGH; CKE is HIGH; t_CK = t_CK(IDD); Other control and address inputs are stable,
Data bus inputs are floating.
I_DD2P
I_DD2N
I_DD2Q
Active Power-Down Current
I_DD3P(0)
All banks open; t_CK = t_CK(IDD), CKE is LOW; Other control and address inputs are stable; Data bus inputs
are floating. MRS A12 bit is set to “0” (Fast Power-down Exit).
Active Power-Down Current
I_DD3P(1)
All banks open; t_CK = t_CK(IDD), CKE is LOW; Other control and address inputs are stable, Data bus inputs
are floating. MRS A12 bit is set to 1 (Slow Power-down Exit);
Active Standby Current
All banks open; t_CK = t_CK(IDD); t_RAS = t_RAS.MAX(IDD), t_RP = t_RP(IDD); CKE is HIGH, CS is HIGH between valid
commands. Address inputs are switching; Data Bus inputs are switching;
I_DD3N
Operating Current
Burst Read: All banks open; Continuous burst reads; BL = 4; AL = 0, CL = CL_(IDD); t_CK = t_CK(IDD);
t_RAS = t_{RAS.MAX.(IDD)}, t_RP = t_RP(IDD); CKE is HIGH, CS is HIGH between valid commands. Address inputs are
switching; Data Bus inputs are switching; I_OUT = 0 mA.
Operating Current
Burst Write: All banks open; Continuous burst writes; BL = 4; AL = 0, CL = CL_(IDD); t_CK = t_CK(IDD);
t_RAS = t_RAS.MAX(IDD), t_RP = t_RP(IDD); CKE is HIGH, CS is HIGH between valid commands. Address inputs are
switching; Data Bus inputs are switching;
I_DD4R
I_DD4W
Burst Refresh Current
t_CK = t_CK(IDD), Refresh command every t_RFC = t_RFC(IDD) interval, CKE is HIGH, CS is HIGH between valid
commands, Other control and address inputs are switching, Data bus inputs are switching.
I_DD5B
Distributed Refresh Current
I_DD5D
t_CK = t_CK(IDD), Refresh command every t_REFI = 7.8 µs interval, CKE is LOW and CS is HIGH between valid
commands, Other control and address inputs are switching, Data bus inputs are switching.
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
1)2)3)4)5)
6)
Rev. 1.3, 2007-07
42
03062006-ZNH8-HURV