COP8AME9 Datasheet, PDF (80/83 Pages) National Semiconductor (TI) – 8-Bit CMOS Flash Microcontroller with 8k Memory, Dual Op Amps, Virtual EEROM, Temperature Sensor,10-Bit A/D and Brownout Reset

23.0 Development Support (Continued)
COP8 Hardware Emulation/Debug Tools -
Hardware Tools for: Real-time Emulation; Target Hardware Debug; Target Design Test.
Product
Description
Source
COP8Flash
COP8 In-Circuit Emulator for Flash Families. Windows based development and
NSC Distributor,
Emulators -
real-time in-circuit emulation tool, with trace (EM=None; DM/IM=32k), s/w
or Order from:
COP8-EMFlash
breakpoints (DM=16, EM/IM=32K), source/symbolic debugger, and device
www.cop8.com
COP8-DMFlash
programming. Includes COP8-NSDEV CD, 68pin Null Target, emulation cable with
COP8-IMFlash
2x7 connector, and power supply.
NiceMon Debug A simple, single-step debug monitor with one breadpoint. MICROWIRE interface.
Download from:
Monitor Utility
www.cop8.com
Development and Production Programming Tools -
Programmers for: Design Development; Hardware Test; Pre-Production; Full Production.
Product
Description
Source
COP8 Flash
COP8 Flash Emulators include in-circuit device programming capability during
NSC Distributor, or
Emulators
development.
Order from:
www.cop8.com
NiceMon
National’s software Utilities "KANDAFlash" and "NiceMon" provide development Download from:
Debugger,
In-System-Programming for our Flash Starter Kit, our Prototype Development
www.cop8.com
KANDAFlash
Board, or any other target board with appropriate connectors.
KANDA COP8
The COP8 USB ISP programmer from KANDA is available for engineering, and www.kanda.com
USB ISP
small volume production use. USB interface.
SofTec Micro
The inDart COP8 programmer from SofTec Micro is available for engineering
www.softecmicro.com
inDart COP8
and small volume production use. PC serial interface only.
Third-Party
Third-party programmers and automatic handling equipment are approved for
Various Vendors
Programmers
non-ISP engineering and production use.
Factory
Factory programming available for high-volume requirements.
National
Programming
Representative
23.3 WHERE TO GET TOOLS
Tools can be ordered directly from National, National’s e-store (Worldwide delivery: http://www.national.com/store/) , a National
Distributor, or from the tool vendor. Go to the vendor’s web site for current listings of distributors.
Vendor
Byte Craft Limited
IAR Systems AB
Home Office
421 King Street North
Waterloo, Ontario
Canada N2J 4E4
Tel: [phone]
Fax: [phone]
PO Box 23051
S-750 23 Uppsala
Sweden
Tel: [phone]
Fax [phone]
Electronic Sites
www.bytecraft.com
[e-mail]
www.iar.se
[e-mail]
[e-mail]
[e-mail]
[e-mail]
Embedded Results
LTD.
P.O. Box 200
Aberystwyth,
SY23 2WD, UK
Tel/Fax: [phone]
www.kanda.com
[e-mail]
[e-mail]
Other Main Offices
Distributors Worldwide
USA:: San Francisco
Tel: [phone]
Fax: [phone]
UK: London
Tel: [phone]
Fax: [phone]
Germany: Munich
Tel: [phone]
Fax: [phone]
USA:
Tel/Fax: [phone]
[e-mail]
www.ucpros.com
www.national.com
80