PIC16F870_13 Datasheet, PDF (7/172 Pages) Microchip Technology – 28/40-Pin, 8-Bit CMOS FLASH Microcontrollers

PIC16F870/871
TABLE 1-1: PIC16F870 PINOUT DESCRIPTION
Pin Name
DIP
Pin#
SOIC
Pin#
I/O/P
Type
Buffer
Type
Description
OSC1/CLKI
9
9
I
ST/CMOS^{(3) Oscillator crystal input/external clock source input.}
OSC2/CLKO
10
10
O
—
Oscillator crystal output. Connects to crystal or resonator in
Crystal Oscillator mode. In RC mode, the OSC2 pin outputs
CLKO, which has 1/4 the frequency of OSC1, and denotes the
instruction cycle rate.
MCLR/VPP/THV
1
1
I/P
ST
Master Clear (Reset) input or programming voltage input or High
Voltage Test mode control. This pin is an active low RESET to the
device.
PORTA is a bi-directional I/O port.
RA0/AN0
2
2
I/O
TTL
RA0 can also be analog input 0.
RA1/AN1
3
3
I/O
TTL
RA1 can also be analog input 1.
RA2/AN2/VREF-
4
4
I/O
TTL
RA2 can also be analog input 2 or negative analog reference
voltage.
RA3/AN3/VREF+
5
5
I/O
TTL
RA3 can also be analog input 3 or positive analog reference
voltage.
RA4/T0CKI
6
6
I/O
ST/OD
RA4 can also be the clock input to the Timer0 module. Output
is open drain type.
RA5/AN4
7
7
I/O
TTL
RA5 can also be analog input 4.
PORTB is a bi-directional I/O port. PORTB can be software
programmed for internal weak pull-up on all inputs.
RB0/INT
21
21
I/O
TTL/ST⁽¹⁾
RB0 can also be the external interrupt pin.
RB1
22
22
I/O
TTL
RB2
23
23
I/O
TTL
RB3/PGM
24
24
I/O
TTL/ST⁽¹⁾
RB3 can also be the low voltage programming input.
RB4
25
25
I/O
TTL
Interrupt-on-change pin.
RB5
26
26
I/O
TTL
Interrupt-on-change pin.
RB6/PGC
27
27
I/O
TTL/ST⁽²⁾
Interrupt-on-change pin or In-Circuit Debugger pin. Serial
programming clock.
RB7/PGD
28
28
I/O
TTL/ST⁽²⁾
Interrupt-on-change pin or In-Circuit Debugger pin. Serial
programming data.
PORTC is a bi-directional I/O port.
RC0/T1OSO/T1CKI
11
11
I/O
ST
RC0 can also be the Timer1 oscillator output or Timer1 clock
input.
RC1/T1OSI
12
12
I/O
ST
RC1 can also be the Timer1 oscillator input.
RC2/CCP1
13
13
I/O
ST
RC2 can also be the Capture1 input/Compare1 output/
PWM1 output.
RC3
14
14
I/O
ST
RC4
15
15
I/O
ST
RC5
16
16
I/O
ST
RC6/TX/CK
17
17
I/O
ST
RC6 can also be the USART Asynchronous Transmit or
Synchronous Clock.
RC7/RX/DT
18
18
I/O
ST
RC7 can also be the USART Asynchronous Receive or
Synchronous Data.
VSS
8, 19
8, 19
P
—
Ground reference for logic and I/O pins.
VDD
20
20
P
—
Positive supply for logic and I/O pins.
Legend:
Note 1:
2:
3:
I = input
O = output
I/O = input/output
P = power
OD = Open Drain
— = Not used
TTL = TTL input
ST = Schmitt Trigger input
This buffer is a Schmitt Trigger input when configured as the external interrupt or LVP mode.
This buffer is a Schmitt Trigger input when used in Serial Programming mode.
This buffer is a Schmitt Trigger input when configured in RC Oscillator mode and a CMOS input otherwise.
 2000-2013 Microchip Technology Inc.
DS30569C-page 7