English
Language : 

PIC16LC63A-04 Datasheet, PDF (40/184 Pages) Microchip Technology – 8-Bit CMOS Microcontrollers with A/D Converter
PIC16C63A/65B/73B/74B
6.2 Using Timer0 with an External
Clock
The synchronization of T0CKI with the internal phase
clocks is accomplished by sampling the synchronized
input on the Q2 and Q4 cycles of the internal phase
clocks. Therefore, it is necessary for T0CKI to be high
for at least 2 TOSC (and a small RC delay of 20 ns) and
low for at least 2 TOSC (and a small RC delay of 20 ns).
Refer to the electrical specification for the desired
device.
6.3 Prescaler
There is only one prescaler available which is mutually
exclusively shared between the Timer0 module and the
watchdog timer. A prescaler assignment for the Timer0
REGISTER 6-1:
OPTION_REG REGISTER
R/W-1 R/W-1 R/W-1
RBPU INTEDG T0CS
bit 7
module means that there is no prescaler for the Watch-
dog Timer, and vice-versa. This prescaler is not read-
able or writable (see Figure 6-1).
The PSA and PS2:PS0 bits (OPTION_REG<3:0>)
determine the prescaler assignment and prescale ratio.
When assigned to the Timer0 module, all instructions
writing to the TMR0 register (e.g., CLRF 1, MOVWF 1,
BSF 1,x....etc.) will clear the prescaler. When assigned
to WDT, a CLRWDT instruction will clear the prescaler
along with the Watchdog Timer. The prescaler is not
readable or writable.
Note:
Writing to TMR0, when the prescaler is
assigned to Timer0, will clear the prescaler
count, but will not change the prescaler
assignment.
R/W-1
T0SE
R/W-1
PSA
R/W-1
PS2
R/W-1
PS1
R/W-1
PS0
bit 0
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2-0
RBPU
INTEDG
T0CS: TMR0 Clock Source Select bit
1 = Transition on T0CKI pin
0 = Internal instruction cycle clock (CLKOUT)
T0SE: TMR0 Source Edge Select bit
1 = Increment on high-to-low transition on T0CKI pin
0 = Increment on low-to-high transition on T0CKI pin
PSA: Prescaler Assignment bit
1 = Prescaler is assigned to the WDT
0 = Prescaler is assigned to the Timer0 module
PS2:PS0: Prescaler Rate Select bits
Bit Value TMR0 Rate WDT Rate
000
1:2
1:1
001
1:4
1:2
010
1:8
1:4
011
1 : 16
1:8
100
1 : 32
1 : 16
101
1 : 64
1 : 32
110
1 : 128
1 : 64
111
1 : 256
1 : 128
Legend:
R = Readable bit
-n = Value at POR
W = Writable bit
’1’ = Bit is set
U = Unimplemented bit, read as ‘0’
’0’ = Bit is cleared x = Bit is unknown
Note:
To avoid an unintended device RESET, the instruction sequence shown in the PICmicro™ Mid-Range MCU
Family Reference Manual (DS33023, Section 11.6) must be executed when changing the prescaler assign-
ment from Timer0 to the WDT. This sequence must be followed even if the WDT is disabled.
DS30605C-page 40
 2000 Microchip Technology Inc.