PIC16LC63A-04 Datasheet, PDF (11/184 Pages) Microchip Technology – 8-Bit CMOS Microcontrollers with A/D Converter

PIC16C63A/65B/73B/74B
TABLE 3-1: PIC16C63A/73B PINOUT DESCRIPTION
Pin Name
DIP
Pin#
SOIC
Pin#
I/O/P
Type
Buffer
Type
Description
OSC1/CLKIN
OSC2/CLKOUT
9
9
10
10
I
ST/CMOS⁽³⁾ Oscillator crystal input/external clock source input.
O
—
Oscillator crystal output. Connects to crystal or resonator in
crystal oscillator mode. In RC mode, the OSC2 pin outputs
CLKOUT which has 1/4 the frequency of OSC1, and denotes
the instruction cycle rate.
MCLR/VPP
1
1
I/P
ST
Master clear (RESET) input or programming voltage input.
This pin is an active low RESET to the device.
PORTA is a bi-directional I/O port.
RA0/AN0⁽⁴⁾
2
2
I/O
TTL
RA0 can also be analog input 0⁽⁴⁾.
RA1/AN1⁽⁴⁾
3
3
I/O
TTL
RA1 can also be analog input 1⁽⁴⁾.
RA2/AN2⁽⁴⁾
4
4
I/O
TTL
RA2 can also be analog input 2⁽⁴⁾.
RA3/AN3/VREF⁽⁴⁾
5
5
I/O
TTL
RA3 can also be analog input 3 or analog reference
voltage⁽⁴⁾.
RA4/T0CKI
RA5/SS/AN4⁽⁴⁾
6
6
I/O
ST
RA4 can also be the clock input to the Timer0 module.
Output is open drain type.
7
7
I/O
TTL
RA5 can also be analog input 4⁽⁴⁾ or the slave select for
the synchronous serial port.
RB0/INT
21
21
PORTB is a bi-directional I/O port. PORTB can be software
programmed for internal weak pull-up on all inputs.
I/O
TTL/ST⁽¹⁾
RB0 can also be the external interrupt pin.
RB1
22
22
I/O
TTL
RB2
23
23
I/O
TTL
RB3
24
24
I/O
TTL
RB4
25
25
I/O
TTL
Interrupt-on-change pin.
RB5
RB6
RB7
26
26
27
27
28
28
I/O
TTL
Interrupt-on-change pin.
I/O
TTL/ST⁽²⁾
Interrupt-on-change pin. Serial programming clock.
I/O
TTL/ST⁽²⁾
Interrupt-on-change pin. Serial programming data.
PORTC is a bi-directional I/O port.
RC0/T1OSO/T1CKI 11
11
I/O
ST
RC0 can also be the Timer1 oscillator output or Timer1
clock input.
RC1/T1OSI/CCP2
12
12
I/O
ST
RC1 can also be the Timer1 oscillator input or Capture2
input/Compare2 output/PWM2 output.
RC2/CCP1
13
13
I/O
ST
RC2 can also be the Capture1 input/Compare1
output/PWM1 output.
RC3/SCK/SCL
14
14
I/O
ST
RC3 can also be the synchronous serial clock input/output
for both SPI and I²C modes.
RC4/SDI/SDA
15
15
I/O
ST
RC4 can also be the SPI Data In (SPI mode) or
data I/O (I²C mode).
RC5/SDO
16
16
I/O
ST
RC5 can also be the SPI Data Out (SPI mode).
RC6/TX/CK
17
17
I/O
ST
RC6 can also be the USART Asynchronous Transmit
or Synchronous Clock.
RC7/RX/DT
18
18
I/O
ST
RC7 can also be the USART Asynchronous Receive
or Synchronous Data.
VSS
8, 19 8, 19
P
—
Ground reference for logic and I/O pins.
VDD
20
20
P
—
Positive supply for logic and I/O pins.
Legend: I = input
O = output
I/O = input/output
P = power
— = Not used TTL = TTL input ST = Schmitt Trigger input
Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt.
2: This buffer is a Schmitt Trigger input when used in Serial Programming mode.
3: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.
4: A/D module is not available in the PIC16C63A.
 2000 Microchip Technology Inc.
DS30605C-page 11