PIC16LC63A-04 Datasheet, PDF (13/184 Pages) Microchip Technology – 8-Bit CMOS Microcontrollers with A/D Converter

PIC16C63A/65B/73B/74B
TABLE 3-2:
Pin Name
PIC16C65B/74B PINOUT DESCRIPTION (CONTINUED)
DIP
Pin#
PLCC
Pin#
TQFP
MQFP
Pin#
I/O/P
Type
Buffer
Type
Description
PORTC is a bi-directional I/O port.
RC0/T1OSO/T1CKI 15
16
32 I/O
ST
RC0 can also be the Timer1 oscillator output or a
Timer1 clock input.
RC1/T1OSI/CCP2 16
18
35 I/O
ST
RC1 can also be the Timer1 oscillator input or Capture2
input/Compare2 output/PWM2 output.
RC2/CCP1
17
19
36 I/O
ST
RC2 can also be the Capture1 input/Compare1 output/
PWM1 output.
RC3/SCK/SCL
18
20
37 I/O
ST
RC3 can also be the synchronous serial clock input/
output for both SPI and I²C modes.
RC4/SDI/SDA
23
25
42 I/O
ST
RC4 can also be the SPI Data In (SPI mode) or
data I/O (I²C mode).
RC5/SDO
24
26
43 I/O
ST
RC5 can also be the SPI Data Out
(SPI mode).
RC6/TX/CK
25
27
44 I/O
ST
RC6 can also be the USART Asynchronous Transmit or
Synchronous Clock.
RC7/RX/DT
26
29
1
I/O
ST
RC7 can also be the USART Asynchronous Receive or
Synchronous Data.
RD0/PSP0
RD1/PSP1
RD2/PSP2
RD3/PSP3
RD4/PSP4
RD5/PSP5
RD6/PSP6
RD7/PSP7
19
21
20
22
21
23
22
24
27
30
28
31
29
32
30
33
PORTD is a bi-directional I/O port or parallel slave port
when interfacing to a microprocessor bus.
38
I/O
ST/TTL⁽³⁾
39
I/O
ST/TTL⁽³⁾
40
I/O
ST/TTL⁽³⁾
41
I/O
ST/TTL⁽³⁾
2
I/O ST/TTL⁽³⁾
3
I/O ST/TTL⁽³⁾
4
I/O ST/TTL⁽³⁾
5
I/O ST/TTL⁽³⁾
RE0/RD/AN5⁽⁵⁾
RE1/WR/AN6⁽⁵⁾
RE2/CS/AN7⁽⁵⁾
8
9
9
10
10
11
PORTE is a bi-directional I/O port.
25
I/O
ST/TTL⁽³⁾
RE0 can also be read control for the parallel slave port,
or analog input 5⁽⁵⁾.
26
I/O
ST/TTL⁽³⁾
RE1 can also be write control for the parallel slave port,
or analog input 6⁽⁵⁾.
27
I/O
ST/TTL⁽³⁾
RE2 can also be select control for the parallel slave
port, or analog input 7⁽⁵⁾.
VSS
12,31 13,34 6,29 P
—
Ground reference for logic and I/O pins.
VDD
11,32 12,35 7,28 P
—
Positive supply for logic and I/O pins.
NC
— 1,17,28, 12,13,
—
These pins are not internally connected. These pins should
40 33,34
be left unconnected.
Legend: I = input
— = Not used
O = output
TTL = TTL input
I/O = input/output
P = power
ST = Schmitt Trigger input
Note 1: This buffer is a Schmitt Trigger input when configured as the external interrupt.
2: This buffer is a Schmitt Trigger input when used in Serial Programming mode.
3: This buffer is a Schmitt Trigger input when configured as general purpose I/O and a TTL input when used in the Parallel
Slave Port mode (for interfacing to a microprocessor bus).
4: This buffer is a Schmitt Trigger input when configured in RC oscillator mode and a CMOS input otherwise.
5: A/D is not available on the PIC16C65B.
 2000 Microchip Technology Inc.
DS30605C-page 13