PIC16LC63A-04 Datasheet, PDF (31/184 Pages) Microchip Technology – 8-Bit CMOS Microcontrollers with A/D Converter

PIC16C63A/65B/73B/74B
5.2 PORTB and TRISB Registers
PORTB is an 8-bit wide, bi-directional port. The corre-
sponding data direction register is TRISB. Setting a bit
in the TRISB register puts the corresponding output
driver in a hi-impedance input mode. Clearing a bit in
the TRISB register puts the contents of the output latch
on the selected pin(s).
Each of the PORTB pins has a weak internal pull-up. A
single control bit can turn on all the pull-ups. This is per-
formed by clearing bit RBPU (OPTION_REG<7>). The
weak pull-up is automatically turned off when the port
pin is configured as an output. The pull-ups are dis-
abled on a Power-on Reset.
FIGURE 5-3:
RBPU⁽²⁾
Data Bus
WR Port
WR TRIS
BLOCK DIAGRAM OF
RB3:RB0 PINS
Data Latch
DQ
CK
VDD
P
Weak
Pull-up
I/O pin⁽¹⁾
TRIS Latch
DQ
CK
TTL
Input
Buffer
RD TRIS
RD Port
QD
EN
RB0/INT
Schmitt Trigger
Buffer
RD Port
Note 1: I/O pins have diode protection to VDD and VSS.
2: To enable weak pull-ups, set the appropriate TRIS
bit(s) and clear the RBPU bit (OPTION_REG<7>).
Four of PORTB’s pins, RB7:RB4, have an
interrupt-on-change feature. Only pins configured as
inputs can cause this interrupt to occur (i.e., any
RB7:RB4 pin configured as an output is excluded from
the interrupt-on-change comparison). The input pins (of
RB7:RB4) are compared with the value latched on the
last read of PORTB. The “mismatch” outputs of
RB7:RB4 are OR’d together to generate the RB Port
Change Interrupt with flag bit RBIF (INTCON<0>).
This interrupt can wake the device from SLEEP. The
user, in the Interrupt Service Routine, can clear the
interrupt in the following manner:
a) Any read or write of PORTB. This will end the
mismatch condition.
b) Clear flag bit RBIF.
A mismatch condition will continue to set flag bit RBIF.
Reading PORTB will end the mismatch condition, and
allow flag bit RBIF to be cleared.
This interrupt-on-mismatch feature, together with soft-
ware configurable pull-ups on these four pins, allow
easy interface to a keypad and make it possible for
wake-up on key depression. Refer to the Embedded
Control Handbook, “Implementing Wake-up on Key
Stroke” (AN552).
The interrupt-on-change feature is recommended for
wake-up on key depression operation and operations
where PORTB is only used for the interrupt-on-change
feature. Polling of PORTB is not recommended while
using the interrupt-on-change feature.
RB0/INT is an external interrupt input pin and is config-
ured using the INTEDG bit (OPTION_REG<6>).
RB0/INT is discussed in detail in Section 13.5.1.
FIGURE 5-4:
BLOCK DIAGRAM OF
RB7:RB4 PINS
RBPU⁽²⁾
Data Bus
WR Port
Data Latch
DQ
CK
VDD
P
Weak
Pull-up
I/O pin⁽¹⁾
TRIS Latch
DQ
WR TRIS
CK
TTL
Input
Buffer
ST
Buffer
RD TRIS
Latch
QD
Set RBIF
RD Port
EN
Q1
From other
RB7:RB4 pins
QD
EN
RB7:RB6 in Serial Programming mode
RD Port
Q3
Note 1: I/O pins have diode protection to VDD and VSS.
2: To enable weak pull-ups, set the appropriate TRIS
bit(s) and clear the RBPU bit (OPTION_REG<7>).
 2000 Microchip Technology Inc.
DS30605C-page 31