PIC18F2455_09 Datasheet, PDF (378/438 Pages) Microchip Technology – 28/40/44-Pin,High-Performance,Enhanced Flash,USB Microcontrollers with nanoWatt Technology

PIC18F2455/2550/4455/4550
28.2 DC Characteristics: Power-Down and Supply Current
PIC18F2455/2550/4455/4550 (Industrial)
PIC18LF2455/2550/4455/4550 (Industrial) (Continued)
PIC18LF2455/2550/4455/4550
(Industrial)
PIC18F2455/2550/4455/4550
(Industrial)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Param
No.
Symbol
Device
Typ Max Units
Conditions
Module Differential Currents (ΔIWDT, ΔIBOR, ΔILVD, ΔIOSCB, ΔIAD)
D022 ΔIWDT
Watchdog Timer 1.3 3.8 μA
1.4 3.8 μA
-40°C
+25°C
VDD = 2.0V
2.0 3.8 μA
+85°C
1.9 4.6 μA
-40°C
2.0 4.6 μA
+25°C
VDD = 3.0V
2.8 4.6 μA
+85°C
4.0 10 μA
-40°C
5.5 10 μA
+25°C
VDD = 5.0V
D022A ΔIBOR
5.6 10 μA
+85°C
Brown-out Reset⁽⁴⁾ 35 40 μA -40°C to +85°C VDD = 3.0V
40 45 μA -40°C to +85°C
0.1
2
μA
-40°C to +85°C
VDD = 5.0V
Sleep mode,
BOREN1:BOREN0 = 10
D022B ΔILVD
High/Low-Voltage 22
Detect⁽⁴⁾ ₂₅
38 μA -40°C to +85°C VDD = 2.0V
40 μA -40°C to +85°C VDD = 3.0V
29 45 μA -40°C to +85°C VDD = 5.0V
D025 ΔIOSCB
Timer1 Oscillator 2.1 4.5 μA
1.8 4.5 μA
-40°C
+25°C
VDD = 2.0V 32 kHz on Timer1⁽³⁾
2.1 4.5 μA
+85°C
2.2 6.0 μA
2.6 6.0 μA
-40°C
+25°C
VDD = 3.0V 32 kHz on Timer1⁽³⁾
2.9 6.0 μA
+85°C
3.0 8.0 μA
3.2 8.0 μA
-40°C
+25°C
VDD = 5.0V 32 kHz on Timer1⁽³⁾
3.4 8.0 μA
+85°C
D026 ΔIAD
A/D Converter 1.0 2.0 μA -40°C to +85°C VDD = 2.0V
1.0 2.0 μA -40°C to +85°C VDD = 3.0V A/D on, not converting
1.0 2.0 μA -40°C to +85°C VDD = 5.0V
Legend:
Note 1:
2:
3:
4:
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS;
MCLR = VDD; WDT enabled/disabled as specified.
Standard low-cost 32 kHz crystals have an operating temperature range of -10°C to +70°C. Extended
temperature crystals are available at a much higher cost.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be
less than the sum of both specifications.
DS39632E-page 376
© 2009 Microchip Technology Inc.