English
Language : 

PIC18F2221_1 Datasheet, PDF (340/402 Pages) Microchip Technology – Enhanced Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology
PIC18F2221/2321/4221/4321 FAMILY
27.2 DC Characteristics: Power-Down and Supply Current
PIC18F2221/2321/4221/4321 (Industrial)
PIC18LF2221/2321/4221/4321 (Industrial) (Continued)
PIC18LF2221/2321/4221/4321
(Industrial)
PIC18F2221/2321/4221/4321
(Industrial, Extended)
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
Standard Operating Conditions (unless otherwise stated)
Operating temperature
-40°C ≤ TA ≤ +85°C for industrial
-40°C ≤ TA ≤ +125°C for extended
Param
No.
Legend:
Note 1:
2:
3:
4:
5:
Device
Typ Max Units
Conditions
Supply Current (IDD)(2)
PIC18LF2X21/4X21 160 230 μA
170 230 μA
170 230 μA
PIC18LF2X21/4X21 220 330 μA
240 330 μA
250 330 μA
All Devices 410 500 μA
420 500 μA
430 500 μA
Extended Devices Only 450 500 μA
PIC18LF2X21/4X21 310 440 μA
330 440 μA
340 440 μA
PIC18LF2X21/4X21 480 750 μA
500 750 μA
520 750 μA
All Devices 0.91 1.3 mA
0.93 1.3 mA
0.96 1.3 mA
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
+125°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
-40°C
+25°C
+85°C
VDD = 2.0V
VDD = 3.0V
VDD = 5.0V
VDD = 2.0V
VDD = 3.0V
VDD = 5.0V
FOSC = 1 MHz
(RC_IDLE mode,
INTOSC source)
FOSC = 4 MHz
(RC_IDLE mode,
INTOSC source)
Extended Devices Only 0.98 1.3 mA
+125°C
Shading of rows is to assist in readability of the table.
The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured
with the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD or VSS, and all features that
add delta current disabled (such as WDT, Timer1 Oscillator, BOR, etc.).
The supply current is mainly a function of operating voltage, frequency and mode. Other factors, such as I/O pin
loading and switching rate, oscillator type and circuit, internal code execution pattern and temperature, also have
an impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail-to-rail; all I/O pins tri-stated, pulled to VDD or VSS;
MCLR = VDD; WDT enabled/disabled as specified.
Low-power, Timer1 oscillator is selected unless otherwise indicated, where LPT1OSC (CONFIG3H<2>) = 1.
BOR and HLVD enable internal band gap reference. With both modules enabled, current consumption will be less
than the sum of both specifications.
When operation below -10°C is expected, use T1OSC High-Power mode, where LPT1OSC (CONFIG3H<2>) = 0.
DS39689F-page 340
© 2009 Microchip Technology Inc.