|
PIC18F23K20 Datasheet, PDF (3/420 Pages) Microchip Technology – 28/40/44-Pin Flash Microcontrollers with 10-Bit A/D and nanoWatt Technology | |||
|
◁ |
PIC18F2XK20/4XK20
28/40/44-Pin Flash Microcontrollers with
10-Bit A/D and nanoWatt Technology
Power-Managed Modes:
⢠Run: CPU on, peripherals on
⢠Idle: CPU off, peripherals on
⢠Sleep: CPU off, peripherals off
⢠Idle mode currents down to 1.0 μA, typical
⢠Sleep mode current down to 0.1 μA, typical
⢠Timer1 Oscillator: 1.0 μA, 32 kHz, 1.8V, typical
⢠Watchdog Timer: 2.0 μA, 1.8V, typical
⢠Two-Speed Oscillator Start-up
Peripheral Highlights:
⢠High-current sink/source 25 mA/25 mA
⢠Three programmable external interrupts
⢠Four independent input-change interrupts
⢠8 independent weak pull-ups
⢠Programmable slew rate
⢠Capture/Compare/PWM (CCP) module
⢠Enhanced Capture/Compare/PWM (ECCP)
module:
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-Shutdown and Auto-Restart
⢠Master Synchronous Serial Port (MSSP) module
supporting 3-wire SPI (all 4 modes) and I2Câ¢
Master and Slave modes with address mask
⢠Enhanced Addressable USART module:
- Supports RS-485, RS-232 and LIN 2.0
- RS-232 operation using internal oscillator
block (no external crystal required)
- Auto-Wake-up on Break
- Auto-Baud Detect
⢠10-bit, up to 14-channel Analog-to-Digital
Converter module (ADC):
- Auto-acquisition capability
- Conversion available during Sleep
- Internal 1.2V Fixed Voltage Reference (FVR)
channel
- Independent input multiplexing
⢠Dual analog comparators
- Rail-to-rail operation
- Independent input multiplexing
⢠Programmable On-Chip Voltage Reference
(CVREF) module (% of VDD)
Flexible Oscillator Structure:
⢠Four Crystal modes, up to 64 MHz
⢠4X Phase Lock Loop (available for crystal and
internal oscillators)
⢠Two External RC modes, up to 4 MHz
⢠Two External Clock modes, up to 64 MHz
⢠Internal oscillator block:
- 8 user selectable frequencies, from 31 kHz to
16 MHz
- Provides a complete range of clock speeds
from 31 kHz to 64 MHz when used with PLL
- User tunable to compensate for frequency drift
⢠Secondary oscillator using Timer1 @ 32 kHz
⢠Fail-Safe Clock Monitor:
- Allows for safe shutdown if primary or secondary
oscillator stops
Special Microcontroller Features:
⢠C compiler optimized architecture:
- Optional extended instruction set designed to
optimize re-entrant code
⢠Self-programmable under software control
⢠Priority levels for interrupts
⢠8 x 8 Single-Cycle Hardware Multiplier
⢠Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 131s
⢠Single-supply 3V In-Circuit Serial
Programming⢠(ICSPâ¢) via two pins
⢠In-Circuit Debug (ICD) via two pins
⢠Operating voltage range: 1.8V to 3.6V
⢠Programmable 16-level High/Low-Voltage
Detection (HLVD) module:
- Supports interrupt on High/Low-Voltage
Detection
⢠Programmable Brown-out Reset (BOR)
- With software enable option
© 2007 Microchip Technology Inc.
Advance Information
DS41303B-page 1
|
▷ |