71M6533 Datasheet, PDF (92/132 Pages) Teridian Semiconductor Corporation – Energy Meter IC

71M6533/G/H and 71M6534/H Data Sheet
QREG[1:0]
RST_SUBSEC
RTCA_ADJ[6:0]
201E[1:0]
2010[0]
2011[6:0]
0
NV
0
NV
40
–
RTC_SEC[5:0
RTC_MIN[5:0]
RTC_HR[4:0]
RTC_DAY[2:0]
RTC_DATE[4:0]
RTC_MO[3:0]
RTC_YR[7:0]
2015
2016
2017
2018
2019
201A
201B
*
NV
*
NV
*
NV
*
NV
*
NV
*
NV
*
NV
RTM_E
RTM0[7:0]
RTM1[7:0]
RTM2[7:0]
RTM3[7:0]
2002[3]
2060[9:8]
2061[7:0]
2062[9:8]
2063[7:0]
2064[9:8]
2064[7:0]
2065[9:8]
2066[7:0]
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
SECURE
SFRB2[6]
0
–
SLEEP
20A9[6]
SEL_IAN
SEL_IBN
SEL_ICN
SEL_IDN
SLOT0_SEL[3:0]
SLOT1_SEL[3:0]
…
SLOT8_SEL[3:0]
SLOT9_SEL[3:0]
20AC[1]
20AC[5]
20AD[1]
20AD[5]
2090[3:0]
2090[7:4]
2094[3:0]
2094[7:4]
0
0
0
0
0
0
0
0
0
0
0
0
1
1
…
…
8
8
9
9
FDS_6533_6534_004
R/W RTC adjust. See Section 1.5.3 Real-Time Clock (RTC) for additional details.
R/W The sub-second counter is restarted when a 1 is written to this bit.
R/W Analog RTC adjust. See Section 1.5.3 Real-Time Clock (RTC) for additional details.
These are the year, month, day, hour, minute and second parameters of the RTC.
Writing to these registers sets the time. Each write to one of these registers must be
preceded by a write to 0x201F (WE). Valid values for each parameter are:
SEC: 00 to 59, MIN: 00 to 59, HR: 00 to 23 (00 = Midnight)
R/W
DAY: 01 to 07 (01 = Sunday), DATE: 01 to 31, MO: 01 to 12
YR: 00 to 99 (00 and all others divisible by 4 are leap years)
Values in the RTC registers are undefined when the IC powers up without a battery but
are maintained through mission and battery modes when a sufficient voltage is maintained
at the VBAT pin. Write operations to these registers are delayed by one second.
There is no change of value at reset if the voltage at VBAT is within specification.
R/W Real Time Monitor enable (RTM). When 0, the RTM output is low.
R/W
The four RTM probes. Before each CE code pass, the values of these registers are
serially output on the RTM pin. The RTM registers are ignored when RTM_E = 0.
When set, enables security provisions that prevent external reading of flash memory
R/W
and CE program RAM (zeros will be returned if the memory is read). It should be set
while PREBOOT is set. SECURE is cleared when the flash is mass-erased and on chip
reset. The bit may only be set, attempts to write zero are ignored.
Puts the 71M6533/71M6534 into SLEEP mode. This bit is ignored if system power is
W present. The 71M6533 and 71M6534 will wake when the autowake timer times out,
when the push button is pushed, when system power returns or when RESET goes high.
R/W
When set to 1, selects differential mode for the corresponding current input (IA, IB, IC,
or ID). When 0, the input remains single-ended.
Primary multiplexer frame analog input selection. These bits map the selected input,
R/W
0-9 to the multiplexer state. The ADC output is always written to the memory location
corresponding to the input, regardless of which multiplexer state an input is mapped to
(see Section 1.1 Error! Not a valid result for table.).
92
Rev 2