ICS1893AFLF Datasheet, PDF (64/136 Pages) Integrated Device Technology – 3.3-V 10Base-T/100Base-TX Integrated PHYceiver™

ICS1893AF Data Sheet - Release
Chapter 8 Management Register Set
8.3.2 100Base-TX Full Duplex (bit 1.14)
The STA reads this bit to learn if the ICS1893AF can support 100Base-TX, full-duplex operations. The
ISO/IEC specification requires that the ICS1893AF must set bit 1.14 to logic:
• Zero if it cannot support 100Base-TX, full-duplex operations.
• One if it can support 100Base-TX, full-duplex operations. (For the ICS1893AF, the default value of bit
1.14 is logic one, in that the ICS1893AF supports 100Base-TX, full-duplex operations.)
Bit 1.14 is a Command Override Write bit, which allows an STA to alter the default value of this bit. [See the
description of bit 16.15, the Command Override Write Enable bit, in Section 8.11, “Register 16: Extended
Control Register”.]
8.3.3 100Base-TX Half Duplex (bit 1.13)
The STA reads this bit to learn if the ICS1893AF can support 100Base-TX, half-duplex operations. The
ISO/IEC specification requires that the ICS1893AF must set bit 1.13 to logic:
• Zero if it cannot support 100Base-TX, half-duplex operations.
• One if it can support 100Base-TX, half-duplex operations. (For the ICS1893AF, the default value of bit
1.13 is logic one. Therefore, when an STA reads the Status Register, the STA is informed that the
ICS1893AF supports 100Base-TX, half-duplex operations.)
This bit 1.13 is a Command Override Write bit, which allows an STA to alter the default value of this bit.
[See the description of bit 16.15, the Command Override Write Enable bit, in Section 8.11, “Register 16:
Extended Control Register”.]
8.3.4 10Base-T Full Duplex (bit 1.12)
The STA reads this bit to learn if the ICS1893AF can support 10Base-T, full-duplex operations. The
ISO/IEC specification requires that the ICS1893AF must set bit 1.12 to logic:
• Zero if it cannot support 10Base-T, full-duplex operations.
• One if it can support 10Base-T, full-duplex operations. (For the ICS1893AF, the default value of bit 1.12
is logic one. Therefore, when an STA reads the Status Register, the STA is informed that the ICS1893AF
supports 10Base-T, full-duplex operations.)
This bit 1.12 is a Command Override Write bit, which allows an STA to alter the default value of this bit.
[See the description of bit 16.15, the Command Override Write Enable bit, in Section 8.11, “Register 16:
Extended Control Register”.]
8.3.5 10Base-T Half Duplex (bit 1.11)
The STA reads this bit to learn if the ICS1893AF can support 10Base-T, half-duplex operations. The
ISO/IEC specification requires that the ICS1893AF must set bit 1.11 to logic:
• Zero if it cannot support 10Base-T, half-duplex operations.
• One if it can support 10Base-T, half-duplex operations. (For the ICS1893AF, the default value of bit 1.11
is logic one. Therefore, when an STA reads the Status Register, the STA is informed that the ICS1893AF
supports 10Base-T, half-duplex operations.)
Bit 1.11 of the ICS1893AF Status Register is a Command Override Write bit., which allows an STA to alter
the default value of this bit. [See the description of bit 16.15, the Command Override Write Enable bit, in
Section 8.11, “Register 16: Extended Control Register”.]
ICS1893AF, Rev D 10/26/04
Copyright © 2004, Integrated Circuit Systems, Inc.
All rights reserved.
64
October, 2004