HDMP-2689 Datasheet, PDF (16/28 Pages) Agilent(Hewlett-Packard) – Quad 2.125/1.0625 GBd Fibre Channel General Purpose SerDes

Table 17. HDMP-2689 AC Electrical Specifications.
T_C = 0°C to T_C = 85°C, V_DDQ = 2.3 to 2.7 V, V_DD = 1.7 to 1.9 V, V_DDA = 1.7 to 1.9 V
Symbol
Parameters
Units
Min
Typ
t_{r, RFCP/N}
RFCP/N LVPECL input rise time, V_{IL, LVPECL} to V_{IH, LVPECL}
ns
1.5
t_f,RFCP/N
RFCP/N LVPECL input fall time, V_{IH, LVPECL} to V_{IL, LVPECL}
ns
1.5
t_{rd, HS_OUT} ^{[1, 5]}
HS_OUT differential rise time, 20% to 80%
ps
150
t_{fd, HS_OUT} ^{[1, 5]}
HS_OUT differential fall time, 80% to 20%
ps
150
t_r,SSTL ^[2,3]
SSTL output rise time, V_{OL, SSTL} to V_{OH, SSTL}
ns
t_f,SSTL ^[2,3]
SSTL output fall time, V_{OH, SSTL} to V_{OL, SSTL}
ns
V_{IP,HS_IN} ^[4]
HS_IN input pk-pk differential voltage
V
0.3
V_{PK,HS_OUT} ^{[1, 5]}
HS_OUT output pk-pk differential voltage, (Z₀= 50Ω)^[1]
V
725
880
V_{Sustain,HS_OUT} ^{[1. 5]} HS_OUT output sustain level differential voltage, (Z₀= 50Ω)^[1]
V
675
830
V_{IP, LVPECL}
RFCP, RFCN input swing (single ended)
V
200
Notes:
1. Measured with 2 pF capacitive load.
2. See Figure 12 for test conditions.
3. SSTL_2 AC Input Signals meet JEDEC Standard No. JESD8-9A test conditions (minimum slew rate 1.0V/ns). See JEDEC Table 3.
4. Note LOS pin description.
5. Measured at default settings, maximum amplitude and medium peaking (11111011).
Max
2.3
1.5
1.6
1050
1000
V_DDA
Table 18. HDMP-2689 Transmitter Section Output Jitter Characteristics.
T_C = 0°C to T_C = 85°C, V_DDQ = 2.3 to 2.7 V, V_DD = 1.7 to 1.9 V, V_DDA = 1.7 to 1.9 V
Symbol
Parameters
Units
Min
Typ Max
RJ ^[1]
Random Jitter at TXnP/N (1s deviation of 50% crossing point)
ps
4
DJ ^[2]
Deterministic Jitter at TXnP/N (peak to peak), K28.5 +/K28.5- pattern
ps
10
DJ ^[3]
Deterministic Jitter at TXnP/N (peak to peak), CRPAT pattern
ps
15
TJ
Total Jitter (TJ=DJ+14*RJ) (K28.5 +/K28.5- pattern)
ps
66
J
Jitter Tolerance
Fibre Channel compliant
Notes:
1. Defined by Fibre Channel specifications X3.230 – 1994 FC-PH, Annex A section A4.4 (oscilloscope method) and tested using setup shown in Figure 20.
2. Defined by Fibre Channel specifications X3.230 – 1994 FC-PH, Annex A section A4.4 and tested using the set up shown in Figure 20.
3. Defined by Fibre Channel Technical Report “Methodologies for Jitter specifications,” Annex B, and tested using the set up shown in Figure 20.
16