MSP430F643 Datasheet, PDF (63/106 Pages) Texas Instruments – MIXED SIGNAL MICROCONTROLLER

MSP430F643x
www.ti.com
SLAS720B – AUGUST 2010 – REVISED AUGUST 2012
LCD_B, Electrical Characteristics
over operating free-air temperature range (unless otherwise noted)
V_LCD
PARAMETER
LCD voltage
TEST CONDITIONS
V_CC
MIN
TYP
MAX UNIT
VLCDx = 0000, VLCDEXT = 0 2.4 V - 3.6 V
V_CC
V
LCDCPEN = 1, VLCDx = 0001 2 V - 3.6 V
2.60
V
LCDCPEN = 1, VLCDx = 0010 2 V - 3.6 V
2.66
V
LCDCPEN = 1, VLCDx = 0011 2 V - 3.6 V
2.72
V
LCDCPEN = 1, VLCDx = 0100 2 V - 3.6 V
2.79
V
LCDCPEN = 1, VLCDx = 0101 2 V - 3.6 V
2.85
V
LCDCPEN = 1, VLCDx = 0110 2 V - 3.6 V
2.92
V
LCDCPEN = 1, VLCDx = 0111 2 V - 3.6 V
2.98
V
LCDCPEN = 1, VLCDx = 1000 2 V - 3.6 V
3.05
V
LCDCPEN = 1, VLCDx = 1001 2 V - 3.6 V
3.10
V
LCDCPEN = 1, VLCDx = 1010 2 V - 3.6 V
3.17
V
LCDCPEN = 1, VLCDx = 1011 2 V - 3.6 V
3.24
V
LCDCPEN = 1, VLCDx = 1100 2 V - 3.6 V
3.30
V
LCDCPEN = 1, VLCDx = 1101 2.2 V - 3.6 V
3.36
V
LCDCPEN = 1, VLCDx = 1110 2.2 V - 3.6 V
3.42
V
LCDCPEN = 1, VLCDx = 1111 2.2 V - 3.6 V
3.48
3.6
V
I_CC,Peak,CP Peak supply currents due to
charge pump activities
LCDCPEN = 1, VLCDx = 1111
2.2 V
400
µA
t_LCD,CP,on Time to charge C_LCD when
discharged
C_LCD = 4.7 µF,
LCDCPEN = 0→1,
VLCDx = 1111
2.2 V
100
500 ms
I_CP,Load
Maximum charge pump load LCDCPEN = 1, VLCDx = 1111
2.2 V
50
µA
current
R_LCD,Seg
R_LCD,COM
LCD driver output impedance,
segment lines
LCD driver output impedance,
common lines
LCDCPEN = 1, VLCDx = 1000,
I_LOAD = ±10 µA
LCDCPEN = 1, VLCDx = 1000,
I_LOAD = ±10 µA
2.2 V
2.2 V
10 kΩ
10 kΩ
12-Bit ADC, Power Supply and Input Range Conditions
over recommended ranges of supply voltage and operating free-air temperature (unless otherwise noted)⁽¹⁾
AV_CC
V_(Ax)
I_{ADC12_A}
PARAMETER
Analog supply voltage
Analog input voltage range⁽²⁾
TEST CONDITIONS
AVCC and DVCC are connected together,
AVSS and DVSS are connected together,
V(AVSS) = V(DVSS) = 0 V
All ADC12 analog input pins Ax
Operating supply current into
AV_CC terminal⁽³⁾
f_ADC12CLK = 5 MHz ⁽⁴⁾
V_CC
2.2 V
3V
MIN TYP MAX UNIT
2.2
3.6 V
0
AV_CC V
150 200
µA
150 250
C_I
Input capacitance
Only one terminal Ax can be selected at one
time
2.2 V
20
25 pF
R_I
Input MUX ON resistance
0 V ≤ VIN ≤ V(AVCC)
10 200 1900 Ω
(1) The leakage current is specified by the digital I/O input leakage.
(2) The analog input voltage range must be within the selected reference voltage range V_R+ to V_R– for valid conversion results. If the
reference voltage is supplied by an external source or if the internal voltage is used and REFOUT = 1, then decoupling capacitors are
required. See REF, External Reference and REF, Built-In Reference.
(3) The internal reference supply current is not included in current consumption parameter I_ADC12.
(4) ADC12ON = 1, REFON = 0, SHT0 = 0, SHT1 = 0, ADC12DIV = 0
Copyright © 2010–2012, Texas Instruments Incorporated
63