DS90UH925Q Datasheet, PDF (17/47 Pages) Texas Instruments – 720p 24-bit Color FPD-Link III Serializer with HDCP

DS90UH925Q
TABLE 1. Configuration Select (MODE_SEL)
# Ideal Ratio
V_R4/V_DD33
Ideal V_R4
(V)
Suggested
Resistor R3
kΩ (1% tol)
Suggested
Resistor R4
kΩ (1% tol)
LFMODE
Repeater
Backward
Compatible
I2S Channel
B
(18–bit
Mode)
1
0
0
Open
40.2 or Any
L
L
L
L
2
0.121
0.399
294
40.2
L
L
L
H
3
0.152
0.502
280
49.9
L
H
L
L
4
0.242
0.799
240
76.8
L
H
L
H
5
0.311
1.026
226
102
H
L
L
L
6
0.402
1.327
196
130
H
L
L
H
7
0.492
1.624
169
165
H
H
L
L
8
0.583
1.924
137
191
H
H
L
H
9
0.629
2.076
124
210
L
L
H^*
L
10 0.727
2.399
90.9
243
H
L
H^*
L
LFMODE:
L = frequency range is 15 – 85 MHz (Default)
H = frequency range is 5 – <15 MHz
Repeater:
L = Repeater OFF (Default)
H = Repeater ON
Backward Compatible:
L = Backward Compatible is OFF (Default)
H = Backward Compatible is ON; DES = DS90UR906Q or DS90UR916Q or DS90UR908Q
– frequency range = 15 - 65MHz when LFMODE = 0
– frequency range = 5 - <15MHz when LFMODE = 1
I2S Channel B:
L = I2S Channel B is OFF, Normal 24-bit RGB Mode (Default)
H = I2S Channel B is ON, 18-bit RGB Mode with I2S_DB Enabled. Note: use of GPIO(s) on unused inputs must be enabled by
register.
GPIO[3:0] and GPO_REG[8:4]
In 18-bit RGB operation mode, the optional R[1:0] and G[1:0] of the DS90UH925Q can be used as the general purpose IOs GPIO
[3:0] in either forward channel (Inputs) or back channel (Outputs) application.
GPIO[3:0] Enable Sequence
See Table 2 for the GPIO enable sequencing.
Step 1: Enable the 18-bit mode either through the configuration register bit Table 6 on DS90UH925Q only. DS90UH926Q is
automatically configured as in the 18-bit mode.
Step 2: To enable GPIO3 forward channel, write 0x03 to address 0x0F on DS90UH925Q, then write 0x05 to address 0x1F on
DS90UH926Q.
TABLE 2. GPIO Enable Sequencing Table
#
Description
1
Enable 18-bit
mode
2
GPIO3
3
GPIO2
4
GPIO1
5
GPIO0
Device
DS90UH925Q
DS90UH926Q
DS90UH925Q
DS90UH926Q
DS90UH925Q
DS90UH926Q
DS90UH925Q
DS90UH926Q
DS90UH925Q
DS90UH926Q
Forward Channel
0x12 = 0x04
Auto Load from DS90UH925Q
0x0F = 0x03
0x1F = 0x05
0x0E = 0x30
0x1E = 0x50
0x0E = 0x03
0x1E = 0x05
0x0D = 0x93
0x1D = 0x95
Back Channel
0x12 = 0x04
Auto Load from DS90UH925Q
0x0F = 0x05
0x1F = 0x03
0x0E = 0x50
0x1E = 0x30
0x0E = 0x05
0x0E = 0x05
0x0D = 0x95
0x1D = 0x93
Copyright © 1999-2012, Texas Instruments Incorporated
17