SMH4804 Datasheet, PDF (1/41 Pages) Summit Microelectronics, Inc. – -48V Programmable Hot Swap Sequencing Power Controller

SMH4804
-48V Programmable Hot Swap Sequencing Power Controller
–
FEATURES AND APPLICATIONS
Features:
• Soft Starts Main Power Supply on Card Insertion or
System Power Up
• In-Rush Current Limiting
• Master Enable to Allow System Control of Power Up or
Down
• Programmable Independent Control of up to 4 DC/DC
Converters via 4 Power Good Signals, PG[4:1]#
• Highly Programmable Circuit Breaker Level and Mode
– Programmable Quick-Trip™ Value, Current
Limiting, Duty Cycle Times, and Over-Current Filter
• Programmable Host Voltage Fault Monitoring
– Programmable UV/OV Filter and UV Hysteresis
• Programmable Fault Mode: Latched or Duty Cycle
• Internal Shunt Regulator Allows for a Wide Supply
Range (typically -32 to -72 Volts)
• I²C 2-Wire Serial Bus Interface for Programming,
Power On/Off and Operational Status
Applications:
• Telecom Hot-Swap Card
• Distributed Power Architectures
• Power-on LAN, IEEE 802.3
–
SIMPLIFIED APPLICATION DRAWING
–
INTRODUCTION
The SMH4804 is a user-programmable -48V power supply
controller designed to control the hot-swapping of plug-in
cards and to sequence supplies in a distributed power
environment. The SMH4804 drives an external power
MOSFET switch that connects the bus side supply to the
card side load and controls in-rush current while providing
both current regulation and over-current protection. When
the source and drain voltages of the external MOSFET are
within specification, the SMH4804 asserts four PG[4:1]#
power-good logic outputs either simultaneously or
sequenced at programmable intervals to enable DC-DC
converters to distribute card side power.
Additional features of the device include: UV and OV
monitor, master enable or temperature sense input (EN/
TS), 2.5V and 5V reference outputs for expanding monitor
functions, two Pin-Detect enable inputs (PD1# and PD2#)
for card insertion verification, and duty-cycle or latched
over-current protection modes. All features are
programmed in nonvolatile registers through the I²C
interface which is simplified with the SMX3200 interface
adapter and Windows GUI software available from Summit
Microelectronics. Engineers can program the device
directly in-circuit with units of voltage, current and time,
allowing fast design cycles.
9 571 9
' 'XDO
00%'
5
9
6KRUW 3LQV

9
5
'
'
9 5
. 
5
. 
9
9
5
. 
'
'
5'
,^&
. :
  

3'
 _3'
     

3* 
 ₈₉
60+
3*  ^

3* 

29
 
&
5
Q)




3* 

1RWH 
&
Q)
5

5
.
&
Q)
5
.
&
Q)
'
00%'
4
,5)1
1RWH  6DIHW\ LVRODWLRQ LQWHUIDFH PD\ EH UHTXLUHG 6HH $SSV 6HFWLRQ
Figure 1. SMH4804 Simplified Application Diagram



9LQ 9RXW
2Q2II
9LQ ^9RXW


9



9LQ 9RXW
2Q2II
9LQ ^9RXW


9



9LQ 9RXW
2Q2II
9LQ ^9RXW


9



9LQ 9RXW
2Q2II
9LQ ^9RXW


9
© SUMMIT Microelectronics, Inc. 2002 • 300 Orchard City Drive #131 • Campbell CA 95006 • Phone [phone] • Fax [phone] • www.summitmicro.com
2050 3.7 10/30/02
1