M16C6C Datasheet, PDF (75/94 Pages) Renesas Technology Corp – RENESAS MCU

M16C/6C Group
5. Electrical Characteristics
5.3 Electrical Characteristics (V_CC1 = V_CC2 = 3 V)
5.3.1 Electrical Characteristics
Table 5.38 Electrical Characteristics (1) ^{(1, 2)}
V_CC1 = V_CC2 = 3 V
Symbol
Parameter
V_OH High
output
P6_0 to P6_7, P7_2 to P7_7,
P8_0 to P8_4, P8_6, P8_7,
voltage P9_0 to P9_7, P10_0 to P10_7
P0_0 to P0_7, P1_0 to P1_7,
P2_0 to P2_7, P3_0 to P3_7,
P4_0 to P4_7, P5_0 to P5_7
V_OH High output voltage XOUT
HIGHPOWER
LOWPOWER
High output voltage XCOUT
HIGHPOWER
Measuring Condition
Standard
Min. Typ.
I_OH = −1 mA
V_CC1 − 0.5
Unit
Max.
V_CC1 V
I_OH = −1 mA
V_CC2 − 0.5
V_CC2
I_OH = −0.1 mA
V_CC1 − 0.5
V_CC1 V
I_OH = −50 μA
V_CC1 − 0.5
V_CC1
With no load applied
2.6
V
LOWPOWER With no load applied
2.2
V_OL Low output P6_0 to P6_7, P7_0 to P7_7,
voltage P8_0 to P8_7, P9_0 to P9_7,
P10_0 to P10_7
I_OL = 1 mA
0.5 V
P0_0 to P0_7, P1_0 to P1_7,
I_OL = 1 mA
0.5
P2_0 to P2_7, P3_0 to P3_7,
P4_0 to P4_7, P5_0 to P5_7
V_OL Low output voltage XOUT
Low output voltage XCOUT
HIGHPOWER
LOWPOWER
HIGHPOWER
I_OL = 0.1 mA
I_OL = 50 μA
With no load applied
0.5 V
0.5
0
V
LOWPOWER With no load applied
V_T+-V_T- Hysteresis HOLD, RDY, TA0IN to TA4IN,
0.2
TB0IN to TB5IN, INT0 to INT7, NMI,
ADTRG, CTS0 to CTS5, SCL0 to SCL5,
SDA0 to SDA5, CLK0 to CLK5,
TA0OUT to TA4OUT, KI0 to KI3,
RXD0 to RXD5, SD, SCLMM, SDAMM
V_T+-V_T- Hysteresis RESET
0.2
I_IH
High input P0_0 to P0_7, P1_0 to P1_7,
current P2_0 to P2_7, P3_0 to P3_7,
P4_0 to P4_7, P5_0 to P5_7,
P6_0 to P6_7, P7_0 to P7_7,
P8_0 to P8_7, P9_0 to P9_7,
P10_0 to P10_7
XIN, RESET, CNVSS
V_I = 3 V
0
1.0 V
1.8 V
4.0 μA
Notes:
1. Referenced to V_CC1 = V_CC2 = 2.7 to 3.3 V, V_SS = 0 V at T_opr = −20 to 85°C/−40 to 85°C unless otherwise
specified.
2. When V_CC1 ≠ V_CC2, refer to 5 V or 3 V standard depending on the voltage.
REJ03B0277-0100 Rev.1.00 Jul.15, 2009
Page 73 of 90