|
M16C6C Datasheet, PDF (46/94 Pages) Renesas Technology Corp – RENESAS MCU | |||
|
◁ |
M16C/6C Group
5. Electrical Characteristics
5.1.2 Recommended Operating Conditions
Table 5.2 Recommended Operating Conditions (1/3) (1)
Symbol
Parameter
Standard
Unit
Min. Typ. Max.
VCC1,
VCC2
Supply voltage (VCC1 ⥠VCC2)
When USB function is used
3.0
5.0
5.5 V
When USB function is not used 2.7
5.0
5.5 V
AVCC Analog supply voltage
VCC1
V
UVCC
USB Supply When USB function is used
Voltage
(When UVCC
pin is input) When USB function is not used
VCC1 = 3.6 to 5.5V
VCC1 = 3.0 to 3.6V
VCC2 = 2.7 to 5.5V
3.0
3.3
3.6 V
3.0
-
VCC1
V
-
VCC1
-
V
VSS
Supply voltage
0
V
AVSS Analog supply voltage
0
V
VIH
High input P3_1 to P3_7, P4_0 to P4_7, P5_0 to P5_7
voltage
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0
(in single-chip mode)
0.8VCC2
0.8VCC2
VCC2
V
VCC2
V
P0_0 to P0_7, P2_0 to P2_7, P3_0
(data input in memory expansion and microprocessor
modes)
0.5VCC2
VCC2
V
P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_7,
P9_0 to P9_7, P10_0 to P10_7
XIN, RESET, CNVSS
0.8VCC1
VCC1
V
P7_0, P7_1, P8_5
0.8VCC1
6.5 V
VIL
Low input P3_1 to P3_7, P4_0 to P4_7, P5_0 to P5_7
0
voltage
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7, P3_0
0
(in single-chip mode)
0.2VCC2 V
0.2VCC2 V
P0_0 to P0_7, P2_0 to P2_7, P3_0
0
(data input in memory expansion and microprocessor
mode)
0.16VCC2 V
P6_0 to P6_7, P7_0 to P7_7, P8_0 to P8_7,
P9_0 to P9_7, P10_0 to P10_7
XIN, RESET, CNVSS
0
0.2VCC1 V
IOH(peak) High peak
output
current
P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7,
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, P8_6, P8_7,
P9_0 to P9_7, P10_0 to P10_7
â10.0 mA
IOH(avg)
High average P0_0 to P0_7, P1_0 to P1_7, P2_0 to P2_7,
output
P3_0 to P3_7, P4_0 to P4_7, P5_0 to P5_7,
current
P6_0 to P6_7, P7_2 to P7_7, P8_0 to P8_4, P8_6, P8_7,
P9_0 to P9_7, P10_0 to P10_7
â5.0 mA
Notes:
1. Referenced to VCC1 = VCC2 = 2.7 to 5.5 V at Topr = â20 to 85°C/-40 to 85°C unless otherwise specified.
2. The average output current is the mean value within 100 ms.
3. The total IOL(peak) for ports P0, P1, P2, P8_6, P8_7, P9, and P10 must be 80 mA max. The total IOL(peak) for
ports P3, P4, P5, P6, P7, and P8_0 to P8_5 must be 80 mA max. The total IOH(peak) for ports P0, P1, and P2
must be â40 mA max. The total IOH(peak) for ports P3, P4, and P5 must be â40 mA max. The total IOH(peak) for
ports P6, P7_2 to P7_7 and P8_0 to P8_4 must be â40 mA max. IOH(peak) for ports P8_6, P8_7, P9, and P10
must be â40 mA max.
REJ03B0277-0100 Rev.1.00 Jul.15, 2009
Page 44 of 90
|
▷ |