RX64M_16 Datasheet, PDF (213/228 Pages) Renesas Technology Corp – 120-MHz 32-bit RX MCU, on-chip FPU, 240 DMIPS, up to 4-MB flash memory

RX64M Group
5.11 Flash Memory Characteristics
5. Electrical Characteristics
Table 5.53 Code Flash Memory Characteristics
Conditions: VCC = AVCC0 = AVCC1 = VCC_USB = V_BATT = 2.7 to 3.6 V, 2.7 ≤ VREFH0 ≤ AVCC0,
VCC_USBA = AVCC_USBA = 3.0 to 3.6 V,
VSS = AVSS0 = AVSS1 = VREFL0 = VSS_USB = VSS1_USBA = VSS2_USBA = PVSS_USBA = AVSS_USBA = 0 V
Temperature range for programming/erasure: T_a = T_opr
FCLK = 4 MHz
20 MHz ≤ FCLK ≤ 60 MHz
Item
Symbol
Unit
Min.
Typ.
Max.
Min.
Typ.
Max.
Programming time
N_PEC  100 times
256 bytes
8 Kbytes
t_P256
—
0.9
t_P8K
—
29
32 Kbytes
t_P32K
—
116
Programming time
N_PEC > 100 times
256 bytes
8 Kbytes
t_P256
—
1.1
t_P8K
—
35
32 Kbytes
t_P32K
—
140
Erasure time
N_PEC  100 times
8 Kbytes
32 Kbytes
t_E8K
—
71
t_E32K
—
254
Erasure time
N_PEC > 100 times
8 Kbytes
32 Kbytes
t_E8K
—
85
t_E32K
—
304
Reprogramming/erasure cycle*¹
N_PEC
1000*²
—
Suspend delay time during programming t_SPD
—
—
First suspend delay time during erasing t_SESD1
—
—
(in suspend priority mode)
13.2
—
0.4
176
—
13
704
—
52
15.8
—
0.5
212
—
16
848
—
64
216
—
39
864
—
141
260
—
47
1040
—
169
—
1000*²
—
264
—
—
216
—
—
6
ms
80
ms
320
ms
7.2
ms
96
ms
384
ms
120
ms
480
ms
144
ms
576
ms
—
Times
120
μs
120
μs
Second suspend delay time during
erasure
(in suspend priority mode)
t_SESD2
—
—
1.7
—
—
1.7
ms
Suspend delay time during erasure
(in erasure priority mode)
Forced stop command
Data hold time*³
FCU reset time
t_SEED
—
—
1.7
—
—
1.7
ms
t_FD
—
—
32
—
—
20
μs
t_DRP
10
—
—
10
—
—
Year
t_FCUR
35
—
—
35
—
—
μs
Note 1.
Note 2.
Note 3.
Definition of reprogram/erase cycle:
The reprogram/erase cycle is the number of erasing for each block. When the reprogram/erase cycle is n times (n = 1000),
erasing can be performed n times for each block. For instance, when 256-byte programming is performed 32 times for different
addresses in 8-Kbyte block and then the entire block is erased, the reprogram/erase cycle is counted as one. However,
programming the same address for several times as one erasing is not enabled (overwriting is prohibited).
This is the minimum number of times to guarantee all the characteristics after reprogramming (guaranteed range is from 1 to the
value of the minimum value).
This shows the characteristics when reprogramming is performed within the specified range, including the minimum value.
R01DS0173EJ0110 Rev.1.10
Oct 24, 2016
Page 213 of 228