M37754FFCGP Datasheet, PDF (24/68 Pages) Mitsubishi Electric Semiconductor – SINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION

PRELIMINARY _{NSootimcee: pTahriasmisentroict} ^{alimfinitsalasrpeescuifbicjeactitotno. change.}
MITSUBISHI MICROCOMPUTERS
M37754FFCGP
M37754FFCHP
SHINGLE-CHIP 16-BIT CMOS MICROCOMPUTER FLASH MEMORY VERSION
DC ELECTRICAL CHARACTERISTICS (Ta = 25 °C, VCC = 5 V ± 10 %, unless otherwise noted)
Symbol
ISB1
ISB2
ICC1
ICC2
ICC3
Parameter
VCC supply current (at standby)
VCC supply current (at read)
VCC supply current (at program)
VCC supply current (at erase)
IPP1
VPP supply current (at read)
IPP2
IPP3
VPPL
VPPH
VPP supply current (at program)
VPP supply current (at erase)
VPP supply voltage (read only)
VPP supply voltage (read/write)
Test conditions
__
VCC = 5.5 V, CE = VIH
V_C_C = 5.5 V,
CE = VCC ± 0.2 V
__
VCC = 5.5 V, CE = VIL,
tRC = 150 ns, IOUT = 0 mA
VPP = VPPH
VPP = VPPH
0≤VPP≤VCC
VCC<VPP≤VCC + 1.0 V
VPP = VPPH
VPP = VPPH
VPP = VPPH
Min.
VCC
11.4
Limits
Typ.
Unit
Max.
1
mA
100
mA
30
mA
30
mA
30
mA
10
mA
100
mA
100
mA
30
mA
30
mA
VCC + 1.0 V
12.0
12.6
V
Note: VIH, VIL, VOH, VOL, IIH, and IIL for the control input, address input, and data input/output pins conform to the standards for microcomputer modes (e.g.,
memory expansion and microprocessor modes).
AC ELECTRICAL CHARACTERISTICS (Ta = 25 °C, VCC = 5 V ± 10 %, unless otherwise noted)
Read-only mode
Symbol
tRC
ta(AD)
ta(CE)
ta(OE)
tCLZ
tOLZ
tDF
tDH
tWRR
Parameter
Read cycle time
Address access time
__
CE access time
__
OE access time
__
Output enable time (after CE)
__
Output enable time (after OE)
__
Output floating time (after OE)
__ __
Output valid time (after CE, OE, address)
Write recovery time (before read)
Limits
Unit
Min.
Max.
150
ns
150
ns
150
ns
55
ns
0
ns
0
ns
35
ns
0
ns
6
ms
Read/Write mode
Symbol
Parameter
tWC
tAS
tAH
tDS
tDH
tWRR
tRRW
tCS
tCH
tWP
tWPH
tDP
tDE
tVSC
Write cycle time
Address set up time
Address hold time
Data setup time
Data hold time
Write recovery time (before read)
Read recovery time (before write)
__
CE setup time
__
CE hold time
Write pulse width
Write pulse waiting time
Program time
Erase time
VPP setup time
Note : The read timing in the read/write mode is the same timing as in the read-only mode.
Limits
Unit
Min.
Max.
150
ns
0
ns
60
ns
50
ns
10
ns
6
ms
0
ms
20
ns
0
ns
60
ns
20
ns
10
ms
9.5
ms
1
ms
24