PIC16LF1847 Datasheet, PDF (354/408 Pages) Microchip Technology – 18/20/28-Pin Flash Microcontrollers with nanoWatt XLP Technology

PIC16(L)F1847
30.3 DC Characteristics: PIC16(L)F1847-I/E (Power-Down) (Continued)
PIC16LF1847
PIC16F1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device Characteristics
Min.
Typ†
Max.
+85°C
Max.
+125°C
Units
VDD
Conditions
Note
Power-down Base Current (IPD)⁽²⁾
D026A*
—
250
—
—
250
—
—
A
1.8 A/D Current (Note 1, Note 3),
—
A
3.0 ^{conversion in progress}
D026A*
—
280
—
—
280
—
—
A
1.8 A/D Current (Note 1, Note 3),
—
A
3.0 ^{conversion in progress}
—
280
—
—
A
5.0
D027
—
2.2
7.0
10
A
1.8 Cap Sense Low Power
—
4.2
9.0
12
A
3.0 ^{Oscillator mode (Note 1)}
D027
—
21
41
—
23
47
45
A
1.8 Cap Sense Low Power
55
A
3.0 ^{Oscillator mode (Note 1)}
—
24
53
68
A
5.0
D027A
—
6.3
9
—
7.9
12
16
A
1.8 Cap Sense Medium Power
21
A
3.0 ^{Oscillator mode (Note 1)}
D027A
—
21
45
—
23
55
50
A
1.8 Cap Sense Medium Power
60
A
3.0 ^{Oscillator mode (Note 1)}
—
25
60
75
A
5.0
D027B
—
16
25
—
41
45
35
A
1.8 Cap Sense High Power
45
A
3.0 ^{Oscillator mode (Note 1)}
D027B
—
23
62
100
A
1.8 Cap Sense High Power
—
25
90
105
A
3.0 ^{Oscillator mode (Note 1)}
—
26
100
115
A
5.0
D028
—
8.0
17
—
8.1
20
22
A
1.8 Comparator Current, Low Power
25
A
3.0 ^{mode, one comparator enabled}
(Note 1)
D028
—
30
50
—
33
60
—
35
65
55
A
1.8 Comparator Current, Low Power
65
A
3.0 ^{mode, one comparator enabled}
85
A
5.0 ^{(Note 1)}
D028A
—
8.2
18
—
8.3
21
24
A
1.8 Comparator Current, Low Power
27
A
3.0 ^{mode, two comparators enabled}
(Note 1)
D028A
—
30
51
—
32
61
—
33
67
56
A
1.8 Comparator Current, Low Power
66
A
3.0 ^{mode, two comparators enabled}
87
A
5.0 ^{(Note 1)}
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1:
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
DS41453A-page 356
Preliminary
 2011 Microchip Technology Inc.