PIC16LF1847 Datasheet, PDF (353/408 Pages) Microchip Technology – 18/20/28-Pin Flash Microcontrollers with nanoWatt XLP Technology

PIC16(L)F1847
30.3 DC Characteristics: PIC16(L)F1847-I/E (Power-Down)
PIC16LF1847
PIC16F1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device Characteristics
Min.
Typ†
Max.
+85°C
Max.
+125°C
Units
VDD
Conditions
Note
Power-down Base Current (IPD)⁽²⁾
D022
— 0.02 1.0
4.0
A
1.8 WDT, BOR, FVR, and T1OSC
— 0.03 1.1
4.8
A
3.0 ^{disabled, all Peripherals Inactive}
D022
—
20
40
—
22
45
50
A
1.8 WDT, BOR, FVR, and T1OSC
55
A
3.0 ^{disabled, all Peripherals Inactive}
—
24
50
60
A
5.0
D023
—
0.3
1.5
10.5
A
1.8 LPWDT Current (Note 1)
—
0.5
2.0
16
A
3.0
D023
—
20
41
56
A
1.8 LPWDT Current (Note 1)
—
22
46
61
A
3.0
—
24
51
71
A
5.0
D023A
—
5.5
25
35
A
1.8 FVR current (Note 1)
—
5.0
27
37
A
3.0
D023A
—
32
65
70
A
1.8 FVR current (Note 1)
—
38
75
80
A
3.0
—
68
115
120
A
5.0
D024
—
8.0
15
20
A
3.0 BOR Current (Note 1)
D024
—
30
55
65
A
3.0 BOR Current (Note 1)
—
33
75
85
A
5.0
D025
—
1.0
4.0
7.0
A
1.8 T1OSC Current (Note 1)
—
1.1
4.5
7.5
A
3.0
D025
—
20
42
47
A
1.8 T1OSC Current (Note 1)
—
23
45
50
A
3.0
—
25
48
53
A
5.0
D026
—
0.1
1.5
4.0
A
1.8 A/D Current (Note 1, Note 3), no
—
0.1
2.0
5.0
A
3.0 ^{conversion in progress}
D026
—
20
40
—
22
45
47
A
1.8 A/D Current (Note 1, Note 3), no
49
A
3.0 ^{conversion in progress}
—
24
50
67
A
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1:
The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
 2011 Microchip Technology Inc.
Preliminary
DS41453A-page 355