PIC16LF1847 Datasheet, PDF (351/408 Pages) Microchip Technology – 18/20/28-Pin Flash Microcontrollers with nanoWatt XLP Technology

PIC16(L)F1847
30.2 DC Characteristics: PIC16(L)F1847-I/E (Industrial, Extended) (Continued)
PIC16LF1847
PIC16F1847
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Device
Characteristics
Min. Typ† Max. Units
VDD
Conditions
Note
D014
—
143
260
A
—
240
450
A
—
300
550
A
1.8 FOSC = 4 MHz
3.0
EC Oscillator mode
Medium-power mode
5.0
Supply Current (IDD)^{(1, 2)}
D015
—
2.0
20
A
1.8 FOSC = 31 kHz
—
4.0
22
A
3.0 ^{LFINTOSC mode}
D015
—
21
45
A
1.8 FOSC = 31 kHz
—
27
50
A
3.0 ^{LFINTOSC mode}
—
28
60
A
5.0
D016
—
110
190
A
—
150
—
A
1.8 FOSC = 500 kHz
3.0 ^{MFINTOSC mode}
D016
—
132
190
A
—
165
230
A
1.8 FOSC = 500 kHz
3.0 ^{MFINTOSC mode}
—
210
280
A
5.0
D017*
—
0.55
0.8
mA
—
0.8
1.25
mA
1.8 FOSC = 8 MHz
3.0 ^{HFINTOSC mode}
D017*
—
0.6
0.9
mA
1.8 FOSC = 8 MHz
—
0.9
1.3
mA
3.0 ^{HFINTOSC mode}
—
1.0
1.5
mA
5.0
D018
—
0.8
1.2
mA
1.8 FOSC = 16 MHz
—
1.3
1.8
mA
3.0 ^{HFINTOSC mode}
D018
—
0.8
1.2
mA
1.8 FOSC = 16 MHz
—
1.3
1.8
mA
3.0 ^{HFINTOSC mode}
—
1.5
2.0
mA
5.0
D019
—
2.1
3.0
mA
3.0 FOSC = 32 MHz
—
2.2
3.3
mA
3.6 ^{HFINTOSC mode (Note 3)}
D019
—
2.2
3.1
mA
3.0 FOSC = 32 MHz
—
2.3
3.4
mA
5.0 ^{HFINTOSC mode (Note 3)}
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are not
tested.
Note 1: The test conditions for all IDD measurements in active operation mode are: OSC1 = external square wave, from
rail-to-rail; all I/O pins tri-stated, pulled to VDD; MCLR = VDD; WDT disabled.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors, such as I/O pin loading
and switching rate, oscillator type, internal code execution pattern and temperature, also have an impact on the current
consumption.
3: 8 MHz internal RC oscillator with 4x PLL enabled.
4: 8 MHz crystal oscillator with 4x PLL enabled.
5: For RC oscillator configurations, current through REXT is not included. The current through the resistor can be extended
by the formula IR = VDD/2REXT (mA) with REXT in k
 2011 Microchip Technology Inc.
Preliminary
DS41453A-page 353