PIC16LF1508 Datasheet, PDF (336/384 Pages) Microchip Technology – 20-Pin Flash, 8-Bit Microcontrollers with nanoWatt XLP Technology

PIC16(L)F1508/9
29.3 DC Characteristics: PIC16(L)F1508/9-I/E (Power-Down)
PIC16LF1508/9
PIC16F1508/9
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
D022
Device Characteristics Min.
Power-down Current (IPD)⁽²⁾
—
—
Typ†
Max.
+85°C
Max.
+125°C
Units
0.025 1.0
7.0
A
0.035 2.0
9.0
A
D022
D022A
D023
D023
— 0.20 2.0
10
A
— 0.25 4.0
12
A
— 0.30 12
15
A
—
10
17
18
A
—
11
22
24
A
—
12
25
30
A
— 0.29 1.5
7
A
— 0.39 2.0
9
A
— 10.5 38
44
A
— 11.3
43
48
A
— 12.5 46
50
A
Conditions
VDD
Note
1.8 Base Current: WDT, BOR, FVR,
3.0 ^{and SOSC disabled, all Peripher-}
als inactive
2.3 WDT, BOR, FVR, and SOSC dis-
3.0 ^{abled, all Peripherals inactive}
(VREGPM = 1; Low-Power mode)
5.0
2.3 Base Current: WDT, BOR, FVR
3.0 ^{and SOSC disabled, all peripheral}
inactive (VREGPM = 0; Normal
5.0 _{Power mode)}
1.8 LPWDT Current (Note 1)
3.0
2.3 LPWDT Current (Note 1)
3.0
5.0
D023A
—
14
44
—
23
48
50
A
1.8 FVR current (Note 1)
54
A
3.0
D023A
D024
—
23
62
65
A
2.3 FVR current (Note 1)
—
30
72
75
A
3.0
—
34
115
120
A
5.0
—
7
14
16
A
3.0 BOR Current (Note 1)
D024
D24A
D24A
—
15
47
—
17
55
—
0.1
4
—
11
47
50
A
3.0 BOR Current (Note 1)
66
A
5.0
14
A
3.0 LPBOR Current (Note 1)
50
A
3.0 LPBOR Current (Note 1)
—
12
52
60
A
5.0
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: The peripheral current is the sum of the base IDD or IPD and the additional current consumed when this peripheral is
enabled. The peripheral  current can be determined by subtracting the base IDD or IPD current from this limit. Max
values should be used when calculating total current consumption.
2: The power-down current in Sleep mode does not depend on the oscillator type. Power-down current is measured with
the part in Sleep mode, with all I/O pins in high-impedance state and tied to VDD.
3: A/D oscillator source is FRC.
DS41609A-page 336
Preliminary
 2011 Microchip Technology Inc.