|
PIC18F25K20T-ISO Datasheet, PDF (3/456 Pages) Microchip Technology – 28/40/44-Pin Flash Microcontrollers with nanoWatt XLP Technology | |||
|
◁ |
PIC18F2XK20/4XK20
28/40/44-Pin Flash Microcontrollers
with nanoWatt XLP Technology
High-Performance RISC CPU:
⢠C Compiler Optimized Architecture:
- Optional extended instruction set designed to
optimize re-entrant code
⢠Up to 1024 bytes Data EEPROM
⢠Up to 64 Kbytes Linear Program Memory
Addressing
⢠Up to 3936 bytes Linear Data Memory Addressing
⢠Up to 16 MIPS Operation
⢠16-bit Wide Instructions, 8-bit Wide Data Path
⢠Priority Levels for Interrupts
⢠31-Level, Software Accessible Hardware Stack
⢠8 x 8 Single-Cycle Hardware Multiplier
Flexible Oscillator Structure:
⢠Precision 16 MHz Internal Oscillator Block:
- Factory calibrated to ± 1%
- Software selectable frequencies range of
31 kHz to 16 MHz
- 64 MHz performance available using PLL â
no external components required
⢠Four Crystal modes up to 64 MHz
⢠Two External Clock modes up to 64 MHz
⢠4X Phase Lock Loop (PLL)
⢠Secondary Oscillator using Timer1 @ 32 kHz
⢠Fail-Safe Clock Monitor:
- Allows for safe shutdown if peripheral clock
stops
- Two-Speed Oscillator Start-up
Special Microcontroller Features:
⢠Operating Voltage Range: 1.8V to 3.6V
⢠Self-Programmable under Software Control
⢠Programmable 16-Level High/Low-Voltage
Detection (HLVD) module:
- Interrupt on High/Low-Voltage Detection
⢠Programmable Brown-out Reset (BOR):
- With software enable option
⢠Extended Watchdog Timer (WDT):
- Programmable period from 4 ms to 131s
⢠Single-Supply 3V In-Circuit Serial
Programming⢠(ICSPâ¢) via Two Pins
⢠In-Circuit Debug (ICD) via Two Pins
Extreme Low-Power Management
with nanoWatt XLP:
⢠Sleep mode: < 100 nA @ 1.8V
⢠Watchdog Timer: < 800 nA @ 1.8V
⢠Timer1 Oscillator: < 800 nA @ 32 kHz and 1.8V
Analog Features:
⢠Analog-to-Digital Converter (ADC) module:
- 10-bit resolution, 13 External Channels
- Auto-acquisition capability
- Conversion available during Sleep
- 1.2V Fixed Voltage Reference (FVR) channel
- Independent input multiplexing
⢠Analog Comparator module:
- Two rail-to-rail analog comparators
- Independent input multiplexing
⢠Voltage Reference (CVREF) module
- Programmable (% VDD), 16 steps
- Two 16-level voltage ranges using VREF pins
Peripheral Highlights:
⢠Up to 35 I/O Pins plus 1 Input-only Pin:
- High-Current Sink/Source 25 mA/25 mA
- Three programmable external interrupts
- Four programmable interrupt-on-change
- Eight programmable weak pull-ups
- Programmable slew rate
⢠Capture/Compare/PWM (CCP) module
⢠Enhanced CCP (ECCP) module:
- One, two or four PWM outputs
- Selectable polarity
- Programmable dead time
- Auto-Shutdown and Auto-Restart
⢠Master Synchronous Serial Port (MSSP) module
- 3-wire SPI (supports all 4 modes)
- I2C⢠Master and Slave modes with address
mask
⢠Enhanced Universal Synchronous Asynchronous
Receiver Transmitter (EUSART) module:
- Supports RS-485, RS-232 and LIN
- RS-232 operation using internal oscillator
- Auto-Wake-up on Break
- Auto-Baud Detect
ï£ 2010 Microchip Technology Inc.
DS41303G-page 3
|
▷ |