PIC24HJ256GP210A-I Datasheet, PDF (248/326 Pages) Microchip Technology – 16-bit Microcontrollers with Advanced Analog

PIC24HJXXXGPX06A/X08A/X10A
TABLE 24-9: DC CHARACTERISTICS: I/O PIN INPUT SPECIFICATIONS
DC CHARACTERISTICS
Standard Operating Conditions: 3.0V to 3.6V
(unless otherwise stated)
Operating temperature -40°C  TA  +85°C for Industrial
-40°C  TA  +125°C for Extended
Param
No.
Symbol
Characteristic
Min Typ⁽¹⁾ Max Units
Conditions
VIL
Input Low Voltage
DI10
I/O pins
VSS
— 0.2 VDD V
DI15
MCLR
VSS
— 0.2 VDD V
DI16
DI18
DI19
I/O Pins with OSC1 or SOSCI VSS
I/O Pins with I²C
VSS
I/O Pins with I²C
VSS
— 0.2 VDD V
— 0.3 VDD V SMBus disabled
— 0.8 V V SMBus enabled
VIH
DI20
Input High Voltage
I/O Pins Not 5V Tolerant⁽⁴⁾ 0.7 VDD —
VDD
V
I/O Pins 5V Tolerant⁽⁴⁾
0.7 VDD —
5.5
V
DI28
SDAx, SCLx
0.7 VDD —
5.5
V SMBus disabled
DI29
SDAx, SCLx
2.1
—
5.5
V SMBus enabled
ICNPU CNx Pull-up Current
DI30
IIL
Input Leakage Current^(2,3)
50
250 400
A VDD = 3.3V, VPIN = VSS
DI50
I/O Pins 5V Tolerant⁽⁴⁾
—
—
±2
A VSS  VPIN  VDD,
Pin at high-impedance
DI51
DI51a
I/O Pins Not 5V Tolerant⁽⁴⁾
I/O Pins Not 5V Tolerant⁽⁴⁾
—
—
±1
A VSS  VPIN  VDD,
Pin at high-impedance,
-40°C  TA  +85°C
—
—
±2
A Shared with external reference
pins, -40°C  TA  +85°C
DI51b
I/O Pins Not 5V Tolerant⁽⁴⁾
—
—
±3.5
A VSS  VPIN  VDD, Pin at
high-impedance,
-40°C  TA  +125°C
DI51c
I/O Pins Not 5V Tolerant⁽⁴⁾
—
—
±8
A Analog pins shared with
external reference pins,
-40°C  TA  +125°C
DI55
MCLR
—
—
±2
A VSS VPIN VDD
DI56
OSC1
—
—
±2
A VSS VPIN VDD,
XT and HS modes
Note 1:
2:
Data in “Typ” column is at 3.3V, 25°C unless otherwise stated.
The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified
levels represent normal operating conditions. Higher leakage current may be measured at different input
voltages.
3: Negative current is defined as current sourced by the pin.
4: See “Pin Diagrams” for a list of 5V tolerant pins.
5: VIL source < (VSS – 0.3). Characterized but not tested.
6: Non-5V tolerant pins VIH source > (VDD + 0.3), 5V tolerant pins VIH source > 5.5V. Characterized but not
tested.
7: Digital 5V tolerant pins cannot tolerate any “positive” input injection current from input sources > 5.5V.
8: Injection currents > | 0 | can affect the ADC results by approximately 4-6 counts.
9: Any number and/or combination of I/O pins not excluded under IICL or IICH conditions are permitted pro-
vided the mathematical “absolute instantaneous” sum of the input injection currents from all pins do not
exceed the specified limit. Characterized but not tested.
DS70592D-page 248
 2009-2012 Microchip Technology Inc.