|
PIC24HJ256GP210A-I Datasheet, PDF (1/326 Pages) Microchip Technology – 16-bit Microcontrollers with Advanced Analog | |||
|
PIC24HJXXXGPX06A/X08A/X10A
16-bit Microcontrollers (up to 256 KB Flash and
16 KB SRAM) with Advanced Analog
Operating Conditions
⢠3.0V to 3.6V, -40ºC to +150ºC, DC to 20 MIPS
⢠3.0V to 3.6V, -40ºC to +125ºC, DC to 40 MIPS
Core: 16-bit PIC24H CPU
⢠Code-efficient (C and Assembly) architecture
⢠Single-cycle mixed-sign MUL plus hardware divide
Clock Management
⢠±2% internal oscillator
⢠Programmable PLLs and oscillator clock sources
⢠Fail-Safe Clock Monitor (FSCM)
⢠Independent Watchdog Timer (WDT)
⢠Fast wake-up and start-up
Power Management
⢠Low-power management modes (Sleep, Idle,
Doze)
⢠Integrated Power-on Reset and Brown-out Reset
⢠1.35 mA/MHz dynamic current (typical)
⢠55 μA IPD current (typical)
Advanced Analog Features
⢠Two ADC modules:
- Configurable as 10-bit, 1.1 Msps with four
S&H or 12-bit, 500 ksps with one S&H
- 18 analog inputs on 64-pin devices and up to
32 analog inputs on 100-pin devices
⢠Flexible and independent ADC trigger sources
Timers/Output Compare/Input Capture
⢠Up to nine 16-bit timers/counters. Can pair up to
make four 32-bit timers.
⢠Eight Output Compare modules configurable as
timers/counters
⢠Eight Input Capture modules
Communication Interfaces
⢠Two UART modules (10 Mbps)
- With support for LIN 2.0 protocols and IrDA®
⢠Two 4-wire SPI modules (15 Mbps)
⢠Up to two I2C⢠modules (up to 1 Mbaud) with
SMBus support
⢠Up to two Enhanced CAN (ECAN) modules
(1 Mbaud) with 2.0B support
⢠Data Converter Interface (DCI) module with I2S
codec support
Input/Output
⢠Sink/Source up to 10 mA (pin specific) for stan-
dard VOH/VOL, up to 16 mA (pin specific) for non-
standard VOH1
⢠5V-tolerant pins
⢠Selectable open drain, pull-ups, and pull-downs
⢠Up to 5 mA overvoltage clamp current
⢠External interrupts on all I/O pins
Qualification and Class B Support
⢠AEC-Q100 REVG (Grade 1 -40ºC to +125ºC)
⢠AEC-Q100 REVG (Grade 0 -40ºC to +150ºC)
⢠Class B Safety Library, IEC 60730
Debugger Development Support
⢠In-circuit and in-application programming
⢠Two program and two complex data breakpoints
⢠IEEE 1149.2-compatible (JTAG) boundary scan
⢠Trace and run-time watch
Packages
Type
QFN
Pin Count
64
Contact Lead/Pitch
0.50
I/O Pins
53
Dimensions
9x9x0.9
Note: All dimensions are in millimeters (mm) unless specified.
TQFP
64
0.50
53
10x10x1
TQFP
100
0.50
85
12x12x1
TQFP
100
0.40
85
14x14x1
ï£ 2009-2012 Microchip Technology Inc.
DS70592D-page 1
|
▷ |