PIC16LF720_11 Datasheet, PDF (192/244 Pages) Microchip Technology – 20-Pin Flash Microcontrollers with nanoWatt XLP Technology

PIC16(L)F720/721
23.4
DC Characteristics: PIC16(L)F720/721-I/E
DC CHARACTERISTICS
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C  TA  +85°C for industrial
-40°C  TA  +125°C for extended
Param
No.
Sym.
Characteristic
Min.
Typ†
Max. Units
Conditions
VIL
Input Low Voltage
I/O PORT:
D030
with TTL buffer
—
—
0.8
V 4.5V  VDD  5.5V
D030A
—
—
0.15 VDD V 1.8V  VDD  4.5V
D031
with Schmitt Trigger buffer
—
with I²C™ levels
—
—
0.2 VDD V 2.0V  VDD  5.5V
—
0.3 VDD V
D032
MCLR, OSC1 (RC mode)
—
—
0.2 VDD V
D033A
OSC1 (HS mode)
—
—
0.3 VDD V
VIH
Input High Voltage
I/O ports:
—
—
D040
with TTL buffer
2.0
—
—
V 4.5V  VDD 5.5V
D040A
0.25 VDD +
—
0.8
—
V 1.8V  VDD  4.5V
D041
with Schmitt Trigger buffer 0.8 VDD
—
with I²C™ levels
0.7 VDD
—
—
V 2.0V  VDD  5.5V
—
V
D042
MCLR
0.8 VDD
—
—
V
D043A
OSC1 (HS mode)
0.7 VDD
—
—
V
D043B
IIL
OSC1 (RC mode)
Input Leakage Current⁽¹⁾
0.9 VDD
—
—
V
D060
D061
I/O ports
MCLR⁽²⁾
MCLR⁽³⁾
—
±5
± 125 nA VSS  VPIN  VDD, Pin at high-
impedance, 85°C
±5
± 1000 nA 125°C
—
± 50
± 200
nA VSS  VPIN  VDD, 85°C
—
±300 ±1500 nA 125°C
IPUR
PORTB Weak Pull-up Current
D070*
VOL
Output Low Voltage⁽³⁾
25
100
200
VDD = 3.3V, VPIN = VSS
25
140
300
A VDD = 5.0V, VPIN = VSS
D080
I/O ports
VOH
Output High Voltage⁽³⁾
IOL = 8mA, VDD = 5V
—
—
0.6
V IOL = 6mA, VDD = 3.3V
IOL = 1.8mA, VDD = 1.8V
D090
I/O ports
VDD - 0.7
—
IOH = 3.5mA, VDD = 5V
—
V IOH = 3mA, VDD = 3.3V
IOH = 1mA, VDD = 1.8V
CIO
Capacitive Loading Specs on Output Pins
D101A*
All I/O pins
—
—
50
pF
EP
Program Flash Memory
D130
Cell Endurance
1k
10k
—
E/W Temperature during programming:
10°C  TA  40°C
D131
VDD for Read
VMIN
—
—
V
Legend: TBD = To Be Determined
* These parameters are characterized but not tested.
† Data in “Typ” column is at 3.0V, 25°C unless otherwise stated. These parameters are for design guidance only and are
not tested.
Note 1: Negative current is defined as current sourced by the pin.
2: The leakage current on the MCLR pin is strongly dependent on the applied voltage level. The specified levels represent
normal operating conditions. Higher leakage current may be measured at different input voltages.
3: Including OSC2 in CLKOUT mode.
DS41430B-page 192
Preliminary
 2011 Microchip Technology Inc.