PIC16F872 Datasheet, PDF (128/160 Pages) Microchip Technology – 28-Pin, 8-Bit CMOS FLASH Microcontroller

PIC16F872
14.2 DC Characteristics: PIC16LF872 (Industrial)
DC CHARACTERISTICS
Param
No.
Characteristic
Standard Operating Conditions (unless otherwise stated)
Operating temperature -40°C ≤ TA ≤ +85°C for industrial
Sym Min Typ† Max Units
Conditions
D001
D002*
D003
D004*
D005
D010
Supply Voltage
VDD
RAM Data Retention
VDR
Voltage (Note 1)
VDD start voltage to
VPOR
ensure internal Power-on
Reset signal
VDD rise rate to ensure SVDD
internal Power-on Reset
signal
Brown-out Reset Voltage VBOR
Supply Current (Note 2,5) IDD
2.0
-
-
0.05
3.7
-
- 5.5
1.5 -
V LP, XT, RC osc configuration (DC - 4 MHz)
V
VSS - V See section on Power-on Reset for details
-
- V/ms See section on Power-on Reset for details
4.0 4.35 V BODEN bit in configuration word enabled
0.6 2.0 mA XT, RC osc configuration
FOSC = 4 MHz, VDD = 3.0V (Note 4)
D010A
- 20 35 µA LP osc configuration
FOSC = 32 kHz, VDD = 3.0V, WDT disabled
D015* Brown-out Reset Current ∆IBOR -
(Note 6)
85 200 µA BOR enabled VDD = 5.0V
D020 Power-down Current
IPD
D021 (Note 3,5)
D021A
- 7.5 30 µA VDD = 3.0V, WDT enabled, -40°C to +85°C
- 0.9 5 µA VDD = 3.0V, WDT disabled, 0°C to +70°C
- 0.9 5 µA VDD = 3.0V, WDT disabled, -40°C to +85°C
D023* Brown-out Reset Current ∆IBOR -
(Note 6)
85 200 µA BOR enabled VDD = 5.0V
Legend: * These parameters are characterized but not tested.
† Data in "Typ" column is at 5V, 25°C unless otherwise stated. These parameters are for design guidance
only and are not tested.
Note 1: This is the limit to which VDD can be lowered without losing RAM data.
2: The supply current is mainly a function of the operating voltage and frequency. Other factors such as I/O pin
loading and switching rate, oscillator type, internal code execution pattern and temperature also have an
impact on the current consumption.
The test conditions for all IDD measurements in active operation mode are:
OSC1 = external square wave, from rail to rail; all I/O pins tristated, pulled to VDD
MCLR = VDD; WDT enabled/disabled as specified.
3: The power-down current in SLEEP mode does not depend on the oscillator type. Power-down current is
measured with the part in SLEEP mode, with all I/O pins in hi-impedance state and tied to VDD and VSS.
4: For RC osc configuration, current through REXT is not included. The current through the resistor can be esti-
mated by the formula Ir = VDD/2REXT (mA) with REXT in kOhm.
5: Timer1 oscillator (when enabled) adds approximately 20 µA to the specification. This value is from charac-
terization and is for design guidance only. This is not tested.
6: The ∆ current is the additional current consumed when this peripheral is enabled. This current should be
added to the base IDD or IPD measurement.
DS30221A-page 128
Preliminary
© 1999 Microchip Technology Inc.