1055497-1 Datasheet, PDF (101/320 Pages) Tyco Electronics – RF Coax Products

RF Coax Connectors
SMA Connectors (Continued)
Specifications
General
Material
Finish
MIL-C-39012
Applicable Paragraph
3.3
3.3.1
Design
Electrical
Insulation Resistance
Corona Level
Dielectric Withstanding Voltage
RF High Potential
Contact Resistance
VSWR
RF Leakage
Insertion Loss
Mechanical
Force to Engage
Coupling Nut Retention
Coupling Proof Torque
Cable Retention
Mating Characteristics
3.4
3.11
3.22
3.17
3.23
3.16
3.14
3.26
3.27
3.5.1
3.25
3.6
3.24
3.7
Connector Durability
3.15
Recommended Mating Torque
—
Environmental
Vibration
3.18
Shock
3.19
Thermal Shock
3.20
Corrosion (Salt Spray)
3.13
Moisture Resistance
3.21
Steel corrosion resistant per ASTM-A-582 and ASTM-A-484, Type 303. Beryllium copper per
ASTM-B-196. PTFE Fluorocarbon per ASTM-D-1710.
Center contacts shall be gold plated to a min. thickness of .00127 [.00005] in accordance with
MIL-G-45204, ASTM-B-488. All other metal parts shall be finished as to provide a connector
which meets the corrosion requirements.
The design shall be such that the outline shown in this catalog and the interface dimensions of
MIL-STD-348A are met.
The insulation resistance shall not be less than 10,000 megohms.
Refer to applicable military slash sheet, product drawing or spec.
Refer to applicable military slash sheet, product drawing or spec.
Refer to applicable military slash sheet, product drawing or spec.
Refer to applicable military slash sheet, product drawing or spec.
Refer to applicable military slash sheet, product drawing or spec. Frequency range dependent on
cable used.
Refer to applicable military slash sheet, product drawing or spec.
Refer to applicable military slash sheet, product drawing or spec. Frequency range dependent on
cable used.
The torque required to engage and disengage shall not exceed 2 in.-lbs. The longitudinal force is
not applicable.
60 lbs. min. Applicable for plug connectors only.
15 in.-lbs. min. Applicable for plug connectors only.
Refer to applicable military slash sheet or consult factory.
Applicable to jack connectors only. Reference MIL-STD-348A for dimensions; oversize test pin
.953 [.0375] min. dia., .76 - 1.14 [.030-.045] deep, insertion force 3 lbs. max. with .940 [.0370]
min. dia. pin, withdrawal force 1 oz. min. with .902 [.0355] max. dia. pin.
The connector to be tested and its mating connector shall be subjected to 500 insertion and
withdrawal cycles at 12 cycles per minute max. The connector shall show no evidence of
mechanical failure and shall meet the mating characteristic requirements.
7 to 10 in.-lbs.
Specification MIL-STD-202, method 204, test condition D
Specification MIL-STD-202, method 213, test condition I
Refer to applicable military slash sheet or consult factory.
Specification MIL-STD-202, method 101, test condition B.
Specification MIL-STD-202, method 106. No measurements at high humidity. Insulation
resistance shall be at least 200 megohms within 5 minutes of removal from humidity.
Catalog 1307191
Revised 3-07
www.tycoelectronics.com
Dimensions are in millimeters
and inches unless otherwise
specified. Values in brackets
are standard equivalents.
Dimensions are shown for
reference purposes only.
Specifications subject
to change.
USA: 1-800-522-6752
Canada: 1-905-470-4425
Mexico: 01-800-733-8926
C. America: 52-55-1106-0803
101
South America: 55-11-2103-6000
Hong Kong: 852-2735-1628
Japan: 81-44-844-8013
UK: 44-8706-080-208