X3102 Datasheet, PDF (4/32 Pages) Intersil Corporation – 3 Cell Li-Ion Battery Protection and Monitor IC

X3102
Absolute Maximum Ratings
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . .-55 to 125°C
Operating temperature. . . . . . . . . . . . . . . . . . . . . . . . . . .-40 to 85°C
DC output current. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5mA
Lead temperature (soldering 10s) . . . . . . . . . . . . . . . . . . . . . . 300°C
Power supply voltage, VCC . . . . . . . . . . . . . . V_SS-0.5 to V_SS+27.0V
Cell voltage, VCELL. . . . . . . . . . . . . . . . . . . . . . . . . . . -0.5 to 6.75V
Terminal voltage, V_TERM1 (Pins: SCK, SI, SO, CS, AS0, AS1,
AS2, VCS1, VCS2, OVT, UVT, OCT, AO) V_SS-0.5 to V_RGO + 0.5V
Terminal voltage, V_TERM2 (VCELL1) . . . . .V_SS-0.5 to V_CC + 1.0V
Terminal voltage V_TERM3, (all other pins) . .V_SS-0.5 to V_CC + 0.5V
Recommended Operating Conditions
Commercial . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .-20°C to +70°C
Supply Voltage Range . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6V to 24V
CAUTION: Stresses above those listed in “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress only rating and operation of the
device at these or any other conditions above those indicated in the operational sections of this specification is not implied.
DC Electrical Specifications Over the recommended operating conditions, unless otherwise specified
SYMBOL
PARAMETER
TEST CONDITIONS
MIN
MAX UNITS
I_LI Input leakage current (SCK, SI, CS, ASO, AS1, AS2)
I_LO Output leakage current (SO)
V_IL Input LOW voltage (SCK, SI, CS, AS0, AS1, AS2)
(Note 1)
±10
µA
±10
µA
-0.3
V_RGO x 0.3
V
V_IH Input HIGH voltage (SCK, SI, CS, AS0, AS1, AS2)
(Note 1)
V_RGO x 0.7 V_RGO + 0.3 V
VOL1 Output LOW voltage (SO)
VOH1 Output HIGH voltage (SO)
VOL2 Output LOW voltage
(UVP/OCP, OVP/LMON, CB1-CB4)
I_OL = 1.0mA
I_OH = -0.4mA
I_OL = 100µA
0.4
V
V_RGO – 0.8
V
0.4
V
VOH2 Output HIGH voltage
(UVP/OCP, OVP/LMON, CB1-CB4)
I_OH = -20µA
V_CC – 0.4
V
VOL3 Output LOW voltage (RGC)
I_OL = 2mA, RGP = V_CC, RGO = 5V
0.4
V
VOH3 Output HIGH voltage (RGC)
I_OH = -20µA, RGP = V_CC – 4V, RGO = 5V V_CC – 4.0
V
NOTE:
1. V_IL min. and V_IH max. are for reference only and are not 100% tested.
Operating Specifications Over the recommended operating conditions unless otherwise specified
SYMBOL
DESCRIPTION
CONDITION
TYP
MIN (Note 2) MAX UNIT
V_RGO 5V regulated voltage
I_LMT 5VDC voltage regulator current limit
(Note 3)
On power up or at wake-up
4.5
5.5 V
After self-tuning (@ 10mA V_RGO current; 25°C)
4.97 4.99 5.01
After self-tuning (@ 10mA V_RGO current; 0-50°C) (Note 5) 4.95
5.02
After self-tuning (@ 50mA V_RGO current) (Note 5)
4.90
5.00 V
R_LMT = 10Ω
250
mA
Icc1 V_CC supply current (1)
Icc2 V_CC supply current (2)
Icc3 V_CC supply current (3)
Icc4 V_CC supply current (4)
Icc5 V_CC supply current (5)
Normal operation
during nonvolatile EEPROM write
During EEPROM read SCK = 3.3MHz
Sleep mode
Monitor mode AN2, AN1, AN0 not equal to 0
85 250 µA
1.3 2.5 mA
0.9 1.2 mA
1 µA
365 600 µA
4
FN8246.0
December 22, 2004