MC9S08AC16_0911 Datasheet, PDF (301/336 Pages) Freescale Semiconductor, Inc – HCS08 Microcontrollers

Appendix A Electrical Characteristics and Timing Specifications
A.7 Supply Current Characteristics
Table A-7. Supply Current Characteristics
Num C
Parameter
3
1
C ^{Run supply current measured at}
(CPU clock = 2 MHz, f_Bus = 1 MHz)
5
2
C ^{Run supply current measured at}
(CPU clock = 16 MHz, f_Bus = 8 MHz)
Symbol
RI_DD
RI_DD
V_DD
(V)
Typ¹
5 0.988
3 0.570
5 6.84
3
5.5
Max²
1.2⁴
0.770
8⁶
5.70
Unit
Temp
(°C)
mA –40 to 125°C
mA –40 to 125°C
3
P
Run supply current⁷ measured at (CPU
clock = 40 MHz, f_Bus = 20 MHz)
RI_DD
5 16.8 18.5 mA –40 to 125°C
3 11.5 12.5 mA –40 to 125°C
Stop2 mode supply current
4C
S2I_DD
11
0 to 70°C
5 1.36
20
μA –40 to 85°C
60⁴
–40 to 125°C
10.5
0 to 70°C
3 1.05
17
μA –40 to 85°C
50
–40 to 125°C
5
C ^{Stop3 mode supply current}
S3I_DD
12
0 to 70°C
5 1.49
20
μA –40 to 85°C
90⁴
–40 to 125°C
11
0 to 70°C
3 1.15
19
μA –40 to 85°C
85
–40 to 125°C
6
C _{RTI adder to stop2 or stop3}⁸
5
300
500
500
nA
–40 to 85°C
–40 to 125°C
S23I_DDRTI
3
300
500
500
nA
–40 to 85°C
–40 to 125°C
5
116
150
180
μA
–40 to 85°C
–40 to 125°C
7
C LVD adder to stop3 (LVDE = LVDSE = 1) _S3I
DDLVD
3
90
140
160
μA
–40 to 85°C
–40 to 125°C
8
C ^{Adder to stop3 for oscillator enabled9}
(OSCSTEN =1)
S3I
5,3
5
DDOSC
6
μA ^{–40 to 85°C}
8
μA ^{–40 to 125°C}
1 _{Typical values are based on characterization data at 25°C unless otherwise stated. See Figure A-5 through Figure A-7 for}
typical curves across voltage/temperature.
2 _{Values given here are preliminary estimates prior to completing characterization.}
3 _{All modules except ADC active, ICG configured for FBE, and does not include any dc loads on port pins}
4 _{Every unit tested to this parameter. All other values in the Max column are guaranteed by characterization.}
5 _{All modules except ADC active, ICG configured for FBE, and does not include any dc loads on port pins}
6 _{Every unit tested to this parameter. All other values in the Max column are guaranteed by characterization.}
7 _{All modules except ADC active, ICG configured for FBE and does not include any DC loads on port pins}
8 _{Most customers are expected to find that auto-wakeup from stop2 or stop3 can be used instead of the higher current wait}
mode. Wait mode typical is 560 μA at 3 V with f_Bus = 1 MHz.
9 _{Values given under the following conditions: low range operation (RANGE = 0) with a 32.768kHz crystal, low power mode}
(HGO = 0), clock monitor disabled (LOCD = 1).
MC9S08AC16 Series Data Sheet, Rev. 8
Freescale Semiconductor
301